Hook UP, Center Channel | MTX Audio MONITOR6C, MONITOR12 guide

CENTER CHANNEL

MONITOR6C

When using the MONITOR6C as a center channel speaker in a home theater application the following guidelines should be used for optimum performance.

Locate the speaker as close to the center of your TV or monitor as possible (Figure 1). This will anchor the central image of your home theater to the location of the images seen on the screen.

Place the center channel at an equal distance to the listening position as the main speakers are. Also, place the height of the center channel’s tweeter as close to the same height as the main speakers’ tweeters (Figure 3). This will prevent image blurring when sounds are panned from the one side of the room to the other.

Figure 3 Proper Placement of Center Channel Speaker

Overload Protection

The MONITOR10 and MONITOR12 are equipped with an internal overload pro- tection circuit. The overload protection is a two-stage circuit designed to prevent accidental damage caused by overpowering or amplifier clipping.

The first stage is an active compression circuit that protects the midrange and tweeter. Music signals that may be harmful to the midrange or tweeter are com- pressed. The result is a seamless, clear sounding loudspeaker.

The second stage is a PTC switch designed to protect the entire loudspeaker. When the music signal reaches a harmful level or is distorting excessively the PTC switches to a high impedance state, reducing the loudspeaker output dra- matically. Turning the volume control down to a low level for 10 seconds will restore normal operation.

HOOK UP

Note: If your amplifier or receiver has a 4/8Ω switch, optimum perfomance will be achieved using the 4Ω or lowest impedance positon.

Use 16 gauge or heavier speaker wire for connecting to your amplifier or receiver. Cut wire lengths leaving an extra 12” to 24” at each end to allow for moving the speaker or receiver.

Using a wire cutter or a sharp knife, strip 1/2” of insulation off each end of the wire to expose the conductor. Twist wire ends to prevent from fraying. Connect the conductors to the binding posts on the bottom or back of the speaker by unscrew- ing the post enough to expose the hole in the terminal post. Slip the exposed conductor in the hole and tighten the post. Repeat this step for connecting to your amplifier or receiver. Refer to the owner’s manual supplied with your electronics to assist with proper hook up.

Note: To ensure proper performance, make sure that the wire from the red

(+)terminal on the speaker is connected to the red (+) terminal on your amplifier or receiver. Likewise, make sure the wire from the black (-) termi- nal on the speaker is connected to the black (-) terminal on the amplifier or receiver. (Figure 4)

	BLACK RED
BLACK RED	BLACK RED

- +

BLACK RED

FIGURE 4 Connecting Speakers to Amplifier or Receiver

Once your speakers are hooked up, turn on your electronics and test to make sure they are functioning properly. If your speakers sound “thin” with little bass and have a poor center image, one of the speaker wires is probably hooked up backwards. Double check all connections for proper polarity.

MONITOR10, MONITOR12, MONITOR6C, MONITOR6, MONITOR12, MONITOR6, MONITOR6C specifications

MTX Audio is well-known in the audio industry for its high-performance speakers, subwoofers, and amplifiers. Among its notable offerings are the MTX Audio MONITOR Series, which includes the MONITOR6C, MONITOR6, MONITOR10, and MONITOR12. Each of these models provides enthusiasts with exceptional sound quality and innovative technology designed for both casual listeners and dedicated audiophiles.

The MONITOR6C is a standout component speaker that features a 6.5-inch midrange driver paired with a 1-inch tweeter. This combination delivers a powerful sound profile, making it ideal for both music and movie applications. The speaker utilizes MTX's advanced technology, including a high-temperature voice coil and a rigid injection-molded polypropylene cone, which enhance durability and sound reproduction.

The MONITOR6 is a versatile 6.5-inch speaker known for its impressive bass response and clarity. It's designed for those who seek rich sound in a compact form factor. Its robust design includes a sturdy frame to reduce unwanted vibrations, ensuring that audio output remains clean and precise. The dual midrange speakers allow for an enhanced mid-frequency response, perfect for vocals and instrumentals.

For bass enthusiasts, the MONITOR10 and MONITOR12 subwoofers are exceptional choices. The MONITOR10 features a 10-inch woofer, while the MONITOR12 comes with a larger 12-inch woofer, both engineered to deliver deep, resonant bass without distortion. These subwoofers are equipped with advanced cooling technologies that prevent overheating during extended use, ensuring reliability and maintaining sound quality over time.

The MONITOR12 excels in producing low frequencies with authority, making it a favorite among those who enjoy genres like hip-hop and electronic dance music. Meanwhile, the MONITOR10 provides a balanced approach, allowing it to blend seamlessly within sound systems that require enhanced bass without overpowering the overall sound.

All models in the MONITOR series adhere to MTX’s commitment to quality and performance with advanced materials and robust construction. With thoughtful engineering and a focus on user experience, MTX Audio’s MONITOR series continues to set a standard in the loudspeaker market, catering to a wide range of audio preferences and environments. Whether it’s for home theater setups, professional audio, or casual listening, the MONITOR line excels in delivering high-quality sound that meets the demands of today’s discerning listeners.