MOUNTING (cont’d.)
4.Ventilation: Where solvents, water etc. are being evaporated from work in process, it is necessary to provide substantial quanti- ties of ventilation air to carry away the resulting vapors.
FIRE HAZARD: Since Radiant heaters are capable of developing high temperatures, extreme care should be taken to:
A. Keep combustible materials at least 6” away form sides and back of heater housing and its supporting brackets and spaced far enough in front of heater (heating element side) so ther-
mal radiation from the elements will not ignite combustible materials.
B. If combustible materials are being processed, stoppage of process should initiate immediate heater shutdown and interception of residual heat from radiant heaters (use radiation baffles or move heaters away from work).
C. In the case of solvents of an explosive nature, ventilation air must be in sufficient volume to dilute the solvent vapor so that explosive mix- tures cannot occur, refer to NFPA 86, Standard for Ovens and Furnaces.
WIRING
ELECTRIC SHOCK HAZARD. Disconnect all power before installing or servicing heater. Failure to do so could result in personal injury or property dam- age. Heater must be installed or serviced by a qualified person in accordance with the National Electrical Code, NFPA 70.
ELECTRIC SHOCK HAZARD. Any installation involving electric heaters must be performed by a qualified person and must be effectively grounded in accordance with the National Electrical Code to eliminate shock hazard.
1.Electrical connections to the Radiant Panel are made through the
2.Wiring should be run in flexible or rigid metal conduit and must be installed in accordance with the requirements of the National Electric Code and such other local requirements as may be applic- able.
3.Access to the busbars is obtained by removing the screws in the terminal box cover.
NOTE: Where circuit wiring is installed in locations of high ambient temperature, conductors should be insulated in accor- dance with requirements for temperature and voltage.
4.A 9/32” dia. hole is provided at each end of the busbar for the pur- pose of connecting the circuit wiring to the type
OPERATION
FIRE/EXPOSION HAZARD. This heater is not intended for use in hazardous atmospheres where flammable vapors, gases, liquids or other com- bustible atmospheres are present as defined in the National Electrical Code. Failure to comply can result in personal injury or property damage.
The system designer is responsible for the safety of this equipment and should install adequate
CAUTION: For your own safety –
Before energizing this heater:
1.Be sure all electrical connections are tightly made.
2.Be sure that all conductors are properly insulated.
3.Be sure that the terminal cover has been properly replaced.
A. Controlling Radiant Intensity –
Standard Radiant Panels are built to operate at 40 watts per square inch on the element sheath. When it is desired to reduce the radiant intensity, one or more of the following methods may be used.
1.INPUT CONTROLLERS These
are usually connected in holding coil circuit of magnetic contac- tors. See Chromalox Radiant Heater Manual for further informa- tion regarding Input Controllers and Contactors.
2.SOLID STATE THYRISTOR POWER CONTROLLERS For best
B. Maximum Ambient Temperatures –
CHROMALOX Radiant Panels are not recommended for applications in ambient temperatures exceeding 450˚F. Higher ambient temperatures mean shorter heater life.
Maximum work temperature in a given time depends on sev- eral factors: Reflectivity of work, specific heat of work, mass of work, kW input and losses from oven and time of exposure. As work temperature increases, the work loses heat by radiation and by convection to the surrounding ambient. Although it it a general principle of Radiant Heater application that work temperature conventionally exceeds ambient temperature, in cases where extremely high work temperatures are desired, it is necessary to enclose the heaters in order to increase the ambient temperature. If evaporation of a liquid is desired as a result of increasing work temperature, it is necessary to provide ventilation air in order to carry away the evaporated liquid. Under carefully engineered cir- cumstances, a maximum work temperature of 600˚F may be attained.
2