Desa CGR2N Methods For Attaching Mounting Bracket To Wall, Marking Screw Locations

Page 8

NATURAL GAS HEATER

INSTALLATION

Continued

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. Attach mounting bracket to wall in one of two ways

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to wall stud: This method pro- videsthestrongesthold.Insertmountingscrews through mounting bracket and into wall studs.

Attaching to wall anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in Figure 7. If you can, provide greater clear- ances from floor and joining wall.

2.Mark screw locations on wall (see Fig- ure 7).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

6 3/4"

12 1/8"

 

Min.

 

 

AdjoiningWall

Only Insert Mounting 14 1/2"

Screws Through Last

Min.

 

Hole On Each End

 

 

Floor

Figure 7 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 8.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 9). IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 8 - Folding Anchor

Figure 9 - Popping Open Anchor Wings For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater (see Figure 10).

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

Stand-Out Tab

Mounting Bracket

(attached to wall)

 

Figure 10 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate bottom mounting hole. This hole is near the bottom on the back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 4 un- der Attaching To Wall Anchor Method. If installing bottom mounting screw into wall stud, drill hole at marked lo- cation using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacer between bottom mount- ing hole and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten screw until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks.

Figure 11 - Installing Bottom Mounting Screws

8

107292

Image 8
Contents Infrared VENT-FREE Natural GAS Heater What to do if YOU Smell GASSafety Information Natural GAS HeaterProduct Features Product IdentificationLocal Codes UnpackingAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Fresh AIR for Combustion and Ventilation Ventilation AIRVentilation Air From Inside Building Ventilation Air From OutdoorsInstallation Installation ItemsInstalling Heater to Wall Check GAS TypeInstalling Bottom Mounting Screws Methods For Attaching Mounting Bracket To WallMarking Screw Locations Attaching Mounting Bracket To WallConnecting to GAS Supply Gas ConnectionFor Your Safety Read Before Lighting Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections Operating HeaterManual Lighting Procedure Lighting InstructionsTo Select Heating Level To Turn OFF GAS To ApplianceCleaning and Maintenance Inspecting BurnerTroubleshooting Observed Problem Possible Cause RemedyTurn control knob until it locks at desired Observed Problem Possible Cause Specifications Replacement PartsTechnical Service AccessoryParts Centrals Illustrated Parts Breakdown CGR2NParts List KEY Part Number Description QTYWarranty Information

CGR2N specifications

Desa CGR2N is an innovative village concept designed to embrace modern living while preserving a sense of community and sustainability. This development integrates advanced technologies and green practices to create a holistic living experience for its residents. The central philosophy of Desa CGR2N is to foster interconnectedness among residents while providing access to essential amenities and services.

One of the main features of Desa CGR2N is its focus on smart homes. Each residence is equipped with state-of-the-art smart technology that enhances both security and convenience. Home automation systems allow residents to control lighting, heating, and security features through their smartphones, contributing to energy efficiency and enhanced safety. Furthermore, the integration of IoT devices supports real-time data collection, enabling residents to monitor and manage their energy consumption.

In addition to smart homes, Desa CGR2N incorporates renewable energy solutions, such as solar panels and wind turbines. These technologies significantly reduce the carbon footprint of the village, aligning with global sustainability goals. The development also encourages the use of electric vehicles, providing charging stations and infrastructure to support a shift towards greener transportation.

Community spaces are a vital aspect of Desa CGR2N, designed to promote social interaction and collaboration among residents. Parks, sports facilities, and communal gardens are strategically placed throughout the village, fostering a strong sense of belonging. The village layout prioritizes walkability and accessibility, ensuring that essential services, such as schools, healthcare centers, and shopping areas, are within easy reach.

Furthermore, Desa CGR2N emphasizes local food production through urban farming initiatives. Residents can participate in community gardens, which not only provide fresh produce but also educate individuals about sustainable agriculture practices. This focus on self-sufficiency further strengthens the community's resilience against external disruptions.

Overall, Desa CGR2N represents a forward-thinking approach to modern living, combining technology, sustainability, and community engagement. By prioritizing smart home features, renewable energy, and communal spaces, this village creates an environment where residents can thrive both individually and collectively. As urbanization continues to rise, developments like Desa CGR2N may serve as a blueprint for future living spaces that harmonize innovation with a deep sense of community.