Desa SBVBP(A), SBVBN(A) Inspecting Burners, Operating Optional GWMT1 Wall Mounted Thermostat

Page 20

®

B-VENT FREESTANDING FIREPLACE

OPERATING

FIREPLACE

Continued

OPERATING

OPTIONAL GWMT1

WALL MOUNTED

THERMOSTAT

WARNING: Do not connect the thermostat to a power source. Electrical shock and/or a fire haz- ard will occur.

Light the fireplace as instructed in Light- ing Instructions on page 18. Set wall ther- mostat to desired temperature.

This thermostat has been electronically calibrated at the factory and requires no adjustment or leveling.

OPERATING

OPTIONAL BLOWER

ACCESSORY

Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the left just inside the louver panel.

Both the GA3700 manual blower and the DA3610T thermostatically-controlled blower have an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

Note for DA3610T Only: If you are using DA3610T blower with optional themostat (wall mount or remote con- trol) for the fireplace, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.

The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions that will hinder the flow of air.

Upon installation, the thermostat must be allowed to stabilize at room tempera- ture for a minimum of 30 minutes for proper operation.

To turn the fireplace off, adjust thermo- stat to the lowest setting and turn the gas control knob back to PILOT. The pilot will remain lit.

IMPORTANT: To turn the pilot off, turn the control knob on the heater to the OFF position.

INSPECTING

BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if necessary.

The height of the thermopile must be 3/8" to 1/2" above the pilot flame as shown in Figure

49.The flame from the pilot burner must extend beyond the thermopile.

If your pilot assembly does not meet these requirements:

•turn fireplace off (seeTo Turn Off Gas to Appliance, page 18)

•seeTroubleshooting, pages 22 through 24

Thermopile

3/8" to 1/2"

Pilot Burner

Piezo Ignitor

Figure 49 - Pilot Assembly

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions.

If the vent configuration is installed incor- rectly, the flames will lift or “ghost”. This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.

Figure 50 shows a typical flame pattern. If burner flame pattern differs from that described:

•turn fireplace off (seeTo Turn Off Gas to Appliance, page 18)

•seeTroubleshooting, pages 22 through 24

Figure 50 - Typical Flame Pattern

20

105500

Page 19 Page 21
Image 20
Page 19 Page 21
Contents SBVBNA, Sbvbpa Remote Ready For Your SafetyFor Your Safety What to do if YOU Smell GAS Safety Information Vent Freestanding FireplaceProduct Features Product IdentificationLocal Codes OperationPRE-INSTALLATION Preparation Location and Space RequirementsFreestanding Fireplace Assembly Stove Body AssemblyUse an adjustable wrench or a 10mm socket Lift off corrugated box enclosing stove body cratingInstalling Fireplace Into Stove Body Installing Optional Blower Accessory Installing GA3700/DA3610T BlowersInstallation Precautions Venting InstallationInstalling Rear Cover Installation of Listed B-1 Vent Type B-VENT Installation Listed B-0 or GreaterInstalling Vent System in a Chase Checking Vent CapacityChimneys Relining SystemsTroubleshooting Venting Problems High Altitude InstallationFlue GAS Spillage Causes of Spillage and Corrective ActionFireplace Installation Installing GAS Piping to Fireplace LocationInstallation Items Needed Check GAS TypeChecking GAS Connections Connecting Fireplace to GAS SupplyPressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas Connections Installing Optional Wall Mounted Thermostat GWMT1 Back View of Thermostat BaseREMOVING/REPLACING Glass Door Installing Remote ReceiverInstalling 9-Volt Battery in Hand- Held Remote Control Unit Installing LOGS, Lava Rock and Glowing Embers Installing Log NoFor Your Safety Read Before Lighting Manual Lighting ProcedureOperating Fireplace Lighting InstructionsOptional Remote Operation Thermostat Control OperationGhrc Series Operation Ghrct Series OperationOperating Optional Blower Accessory Pilot AssemblyInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatCleaning and Maintenance Glass DoorPilot and Burners LogsPressed in 30 seconds TroubleshootingAfter pilot lights, keep control knob Orifice Inlet gas pressure is too lowCompany Pane/LP or natural gas companyFireplace produces unwanted odors Tions onLow line pressure Pilot is partially cloggedReplacement Parts Technical ServiceWiring Diagram Service HintsSpecifications Sbvbna SbvbpaAccessories Illustrated Parts Breakdown Sbvbna SbvbpaParts List KEY Part Number Description QTYWarranty Information

SBVBN(A), SBVBP(A) specifications

Desa SBVBN(A) and SBVBP(A) are innovative solutions in the realm of wireless communication, designed to enhance connectivity and network efficiency. Each model is tailored for specific applications, making them essential tools in modern telecommunications.

One of the primary features of both the SBVBN(A) and SBVBP(A) models is their support for advanced modulation techniques. These modulations allow for higher data rates and improved spectral efficiency, which are critical for congested environments. By employing technologies such as Orthogonal Frequency-Division Multiplexing (OFDM), these systems can deliver superior performance even in challenging conditions.

In terms of connectivity, SBVBN(A) focuses on boosting signal strength over long distances. This is especially vital in rural areas where traditional infrastructure may be lacking. The system can cover expansive regions with minimal signal degradation, ensuring reliable communication. Meanwhile, SBVBP(A) is optimized for high-density urban settings, capable of handling a large number of simultaneous connections without compromising speed or quality.

The integration of artificial intelligence and machine learning technologies is another standout feature. Both models utilize smart algorithms to analyze network traffic in real-time, enabling dynamic adjustments to optimize performance. This capability is crucial in environments where user demand can fluctuate drastically, allowing for adaptive resource allocation and enhanced user experience.

Power efficiency is also a significant characteristic of Desa SBVBN(A) and SBVBP(A). Equipped with energy-saving technologies, these systems minimize power consumption while maximizing output. This not only reduces operational costs but also aligns with global sustainability goals.

Moreover, the systems are designed with scalability in mind. They can be easily integrated into existing infrastructures, providing a seamless upgrade path for telecommunication providers looking to enhance their services without major overhauls.

Security is a top priority for both products. They incorporate advanced encryption protocols and access controls, ensuring that data transmission remains secure and protecting against potential threats.

In summary, Desa SBVBN(A) and SBVBP(A) represent the future of wireless communication, with their focus on advanced modulation, AI integration, energy efficiency, scalability, and security. These features make them ideal solutions for a variety of applications, ranging from rural connectivity to urban high-density environments, thus playing a significant role in bridging the digital divide and fostering enhanced communication worldwide.
Top Page Image Contents