Front & Rear Connections, Front Panel | Nady Systems XA manual

FRONT & REAR CONNECTIONS

FRONT PANEL		6
1.	POWER SWITCH
To turn the unit ON or OFF, press the upper or lower portion of
this button. Before turning on the amplifier, check all connections
and turn down the level controls. A momentary muting is normal
when turning the amplifier on or off.
(Caution: Always turn on your power amplifier last, after all your
other connected equipment, and always turn off your power
amplifier before your other connected equipment.)
2.	POWER LED INDICATORS
These LEDs illuminate when the power is turned “ON”.
3.	CLIP (PEAK) LED INDICATORS

reduce the output level of the preceding component to avoid audible distortion.

4. SIGNAL LED INDICATORS

These LEDs illuminate to confirm the presence of an input signal greater than 100 mV at that channel of the amplifier

5. PROTECT LED INDICATORS

These LEDs illuminate if the power amplifier’s output connection is shorted or the load impedance is too low. When either of these LEDs is lit up, turn OFF the power and check the output’s connec- tion to verify that it is correct, then turn ON the power again.

These LEDs illuminate if any section of the power amplifier’s output are within 3DB of clipping. Occasional blinking of the LEDs are acceptable, but if they remain on more than intermittently you should turn down either the power amplifier’s level controls or

6. LEVEL CONTROLS

These control the level of signal coming into each channel. The actual voltage gain of the amplifier is shown in dB. Turn these controls counterclockwise if the peak LEDs illuminate steadily (indicating too strong an input signal).

BACK PANEL

7.POWER CONNECTOR

The cord connector is used to connect the AC power source to your power amplifier.

(CAUTION: DO NOT REMOVE THE CENTER GROUNDING PIN.)

8.FUSES

Fuse holders for 20A/250V 3AG fuses. If these fuses continuously blow, shut off the unit and have it serviced by qualified service personnel.

9.GROUND LIFT SWITCH

Switch to right to disconnect the chassis from ground if neces- sary to eliminate hum caused by ground loops.

10. AC VOLTAGE SELECTOR SWITCH

Before plugging in the power cord, check to see that the unit is set for the proper voltage for your area: ~115V (60Hz) or ~230V (50Hz). A cover plate is provided to ensure that this switch is not accidently reset or tampered with between uses.

XA specifications

The Nady Systems XA is a versatile, high-performance audio system designed for various applications, including live sound reinforcement, studio recordings, and broadcasting. This system is particularly known for its reliability, durability, and superior sound quality, making it a favorite among audio professionals and enthusiasts alike.

One of the main features of the Nady Systems XA is its user-friendly interface. It includes intuitive controls that allow users to easily navigate through various settings, ensuring a seamless operation. The system is equipped with advanced wireless technology that minimizes interference and guarantees clear transmission over considerable distances. This feature is particularly advantageous for live performances where musicians require mobility without sacrificing sound quality.

The XA system supports multiple channels, allowing users to connect various instruments and microphones simultaneously. This capability is essential for bands and ensembles, ensuring that every element of the performance is captured without compromising audio fidelity. Moreover, the system is built to accommodate a wide range of frequency ranges, ensuring that all vocal harmonies and musical nuances are reproduced accurately.

In terms of technological advancements, the Nady Systems XA incorporates digital signal processing (DSP) to enhance sound quality and performance. This technology helps in achieving clearer audio by eliminating unwanted noise and feedback, a common issue with traditional sound systems. Additionally, the system boasts a rugged build designed to withstand the rigors of touring and frequent use in various environments.

Another notable characteristic of the XA system is its adaptability. It is compatible with a multitude of microphones, instruments, and other audio equipment. This flexibility makes it an excellent choice for users looking to expand their audio setup without investing in entirely new systems.

Users also appreciate the robust battery life of the Nady Systems XA. The system is designed to run for extended periods on a single charge, making it ideal for long events and performances where power sources are not readily available.

Overall, the Nady Systems XA stands out in the crowded market of audio systems due to its combination of advanced technology, ease of use, and reliable performance. Its ability to deliver crystal-clear sound across various applications places it at the forefront of modern audio solutions. Whether for live performances, studio sessions, or broadcasting, the Nady Systems XA offers a comprehensive audio experience that meets the needs of professionals and hobbyists alike.