Connecting to GAS Supply

INSTALLATION

Installing Heater To Wall (Cont.) Connecting To Gas Supply

INSTALLATION

Continued

Installing Bottom Mounting Screw

1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from wall.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 under Attaching To Wall Anchor Method, page 7. If installing bottom mounting screw into wall stud, drill hole at marked location using 9/64" drill bit.

5.Replace heater on wall.

6.Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11).

7.Tighten screw until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 8 through 10).

Figure 11 - Installing Bottom Mounting Screw

WARNING: This appliance requires a 3/8" NPT (National Pipe Thread) inlet connection to the pres- sure regulator.

WARNING: A qualified service person must con- nect heater to gas supply. Follow all local codes.

WARNING: For natural gas, never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

IMPORTANT: For natural gas, check gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 14 inches of water. If gas line pressure is higher, heater regulator damage could occur.

For more

CAUTION: For propane/LP gas, never connect heater directly to the propane/LP supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and pro- pane/LP supply.

For propane/LP gas, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 12. Pointing the vent down protects it from freezing rain or sleet.

CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in cer- tain areas. Check your local codes. Use pipe of large enough diameter to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur.

Installation must include equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 13, page 9).

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

Propane/LP
Supply Tank	External Regulator
	External Regulator

Vent Pointing Down

Figure 12 - External Regulator With Vent Pointing Down (propane/LP systems only)

visit www..com

110720-01C

VN10A specifications

Desa VN10A is a cutting-edge vehicle that exemplifies innovation in the realm of modern transportation. Designed to cater to the needs of both urban commuters and adventurous drivers, this vehicle combines style, comfort, and practicality, making it a versatile choice for various driving conditions.

One of the standout features of the Desa VN10A is its efficient powertrain. It is equipped with a powerful yet economical engine that balances performance and fuel efficiency, making it ideal for everyday use. The engine showcases advanced technology, including direct fuel injection and turbocharging, providing exceptional power output while reducing emissions. This combination not only enhances the driving experience but also aligns with global efforts toward sustainability.

The exterior design of the Desa VN10A is another notable aspect. With its aerodynamically sculpted body and sleek lines, the vehicle delivers an aesthetic appeal that turns heads on the road. The innovative LED headlight technology offers improved visibility and adds a modern touch to the overall look, while the available range of colors allows for personalization to suit individual preferences.

Inside, the Desa VN10A prioritizes driver and passenger comfort. The spacious cabin is thoughtfully designed, featuring high-quality materials and advanced ergonomics. The seating arrangement allows for ample legroom, making long journeys more enjoyable. Additionally, the advanced infotainment system includes a touch screen display, Bluetooth connectivity, and compatibility with both Apple CarPlay and Android Auto, ensuring a connected driving experience.

Safety is a paramount consideration in the design of the Desa VN10A. The vehicle is equipped with a comprehensive suite of safety features, including adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to provide peace of mind for both the driver and passengers, promoting a secure driving environment.

In summary, the Desa VN10A stands out for its blend of efficiency, style, and advanced technology. Its powerful engine, modern exterior, comfortable interior, and robust safety features make it a remarkable choice for anyone seeking a reliable and stylish vehicle. Whether navigating city streets or exploring the open road, the Desa VN10A is engineered to rise to the occasion, providing an exceptional driving experience that is hard to match.