Installation, Operation, To Start Heater

INSTALLATION OPERATION

INSTALLATION

WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater.

WARNING: Test all gas piping and connections for leaks after installation or servicing. Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.

1.Provide propane supply system (see Propane Supply, page 3).

2.Connect fuel gas fitting on hose/regulator assembly to pro- pane tank(s). Turn fuel gas fitting counterclockwise into threads on tank. Tighten firmly using a wrench. IMPORTANT: Tighten regulator with vent pointing down. Pointing vent down pro- tects regulator from weather damage.

3.Connect hose to the valve inlet. Tighten firmly using a wrench. You must use the regulator supplied with heater even if pro- pane tank has one.

4.Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check valve on propane tank may stop gas flow. If this happens, you may hear a click inside the regulator assembly, this is the check valve closing. To re- set the excess flow check valve, close propane supply valve and open again slowly.

5.Check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected.

6.Close propane supply valve.

	Fuel Gas Fitting
Propane
Supply Valve	Hose
	Regulator
	Vent
	(pointing down)
	Propane Tank

Valve Inlet

OFF
LO	HI
	HI
MED

Hose

Figure 3 - Hose and Valve Inlet

OPERATION

WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater.

TO START HEATER

1.Follow all installation, ventilation, and safety information.

2.Locate heater on stable and level surface. Make sure strong drafts do not blow on heater.

3.Make sure unit is turned off by slightly depressing and turning control knob fully clockwise to OFF.

5.Slightly depress and turn control knob counterclockwise to the LOW position (see Figure 4).

6.With the control knob pushed all the way in, press and release the piezo ignitor button. Keep pressing piezo ignitor button until the burner lights. Hold control knob down for a maxi- mum of 15 seconds while attempting ignition. If heater does not ignite, release control knob and wait 3 minutes before at- tempting reignition.

	Off			Low
Continue Turning Knob	Position			Position
Counterclockwise to
MED and HI	L		OFF	OF	HI
				F
	O
	M	ED	HI	LO	ED
		ED			M

Figure 2 - Regulator With Vent Pointing Down

Piezo Ignitor Button

OFF

MED

Control Knob

Figure 4 - Control Knob and Piezo Ignitor Button Locations

For morevisit www..com

111695-01A

000 Btu/hr Models specifications

The Desa 000 Btu/hr models are a notable addition to the heating and comfort technology market, recognized for their efficiency and robust performance. These models are specifically designed to provide effective heating solutions for residential and commercial spaces, ensuring optimal comfort during colder months.

One of the primary features of the Desa 000 Btu/hr models is their advanced heating technology. These models utilize a high-efficiency burner system that maximizes heat output while minimizing energy consumption, making them an eco-friendly choice for heating needs. This efficiency not only reduces energy bills but also contributes to lower greenhouse gas emissions, aligning with modern sustainability goals.

Additionally, the Desa models are equipped with superior safety features. Each unit comes with a built-in thermostat that ensures precise temperature control, which prevents overheating and maintains an even thermal balance in your space. This is complemented by a safety shut-off mechanism that automatically turns off the heater if any irregularities are detected, ensuring peace of mind for users.

The design of the Desa 000 Btu/hr models is another highlight. They are compact and stylish, allowing for easy integration into various environments without compromising aesthetics. The outer casing is made from durable materials that resist wear and tear, ensuring longevity. Furthermore, the models are available in various finishes, giving customers the freedom to choose one that best suits their decor.

User-friendliness is also a cornerstone of the Desa design philosophy. These models come with intuitive controls that simplify operation. Whether it’s adjusting the heat settings or programming timers, these units are designed to accommodate the needs of diverse users, from tech-savvy individuals to those who prefer straightforward systems.

Moreover, easy installation is a key aspect of the Desa 000 Btu/hr models. Designed for both indoor and outdoor use, these heaters can be set up swiftly with minimal tools, allowing users to enjoy warmth without extensive renovation.

In summary, the Desa 000 Btu/hr models offer a compelling blend of efficiency, safety, and user-centric design, making them an excellent choice for anyone looking to enhance their heating solutions. With advanced technology and appealing aesthetics, these models are positioned as a top option for modern heating needs.