Samsung WM1245AGS/YKJ, WM1245AFS-XTW Drain hose connection procedures, Positioning the drain hose

Page 7

Installing the Washing Machine

Connecting the water supply hose

1. Remove the adaptor from the

 

 

4. Connect the water supply hose to the

water supply hose.

 

 

adaptor. Pull down part (c) of the

 

 

c

water supply hose. When you release

 

 

part (c) the hose automatically connects

 

 

 

 

 

 

to the adaptor making a ’click’ sound.

2. First, using a “+” type screw driver,

 

 

5. Connect the other end of the water

loosen the four screws on the adaptor.

 

 

supply hose to the inlet water valve at

Next, take the adaptor and turn part(b)

 

 

the top of the washer. Screw the hose

following the arrow until there is a 5mm

 

 

clockwise all the way in.

gap.

 

 

 

3. Connect adaptor to the water tap by

 

 

If the water tap has a screw type faucet,

tightening the screws firmly.

 

 

connect the water supply hose to the

Then, turn part (b) following the arrow

a

 

tap as shown.

and put(a) and (b) together.

b

 

 

 

 

 

NOTICE After completing connection, if water leaks from the hose, then repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.

Note: The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.

Drain hose connection procedures

1. Holding down the handle of the drain hose connector, put in the drain hose in desired direction.

: Fix the hose into the drainage hole, and give the hose connector a push to the body to fix the hose.

Positioning the drain hose

The end of the drain hose may be positioned in three ways:

Over the edge of a wash basin.

The drain hose must be placed at a height of between 0 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving.

ln a sink drain pipe branch

The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground.

ln a drain pipe

Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm.

SAMSUNG Washing Machine Owner

s Instructions

5

Image 7
Contents WM1245A WM1290A Safety instructions Before using the applianceTable of Contents Unpacking the Washing Machine Installing the Washing MachineOverview of the washing machine Selecting a location Adjusting the leveling feetRemoving the shipping bolts To connect the water supply hose Connecting the water supply hosePositioning the drain hose Drain hose connection proceduresPlugging in the machine Wiring lnstructionsWashing for the first time Washing a Load of LaundryPutting detergent in the washing machine Overview of the control panel Temperature selection buttonDrying Auto button For the Silver Wash washingChildlockbutton lock function Washing clothes using Fuzzy LogicPause Option Washing clothes manuallyCancel Using Dry courseUsing Clean Tub Using Delay StartFabric Type Load Capacity Washing tips and hintsDraining the washing machine in an emergency Repairing a frozen washing machineCleaning the exterior Maintaining the Washing MachineCleaning the debris filter Cleaning the detergent drawer and recessTo do this Cleaning the water hose mesh filterProblems and solutions TroubleshootingUnderstanding error messages User option Programme ChartAppendix Fabric care chartElectrical warnings Protecting the environment SpecificationDeclaration of conformity Case the Need for Servicing Arises