Procom V50TYLA-BC Clearance to Combustibles, Electrical Connection, Electrical Specifications

Page 4

CLEARANCE TO COMBUSTIBLES

Back…………………………0mm

Sides……………..…………0mm

Floor……………. .…………0mm

Top………………. .…………610mm

ELECTRICAL CONNECTION

A 10 AMP, 220 Volt,50Hz circuit with a properly grounded outlet is required. Preferably, the stove will be on a dedicated circuit. Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is on operation. The unit comes standard with a 6’ (1828mm) long three wire cord exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord. If an extention cord must be used, it must be a minumum 1.0 mm2 three wire with grounding type plug connector and rated no less than 1900 Watts.

WARNING: Electrical outlet wiring must comply with local building codes and all other applicable regulations to reduce the risk of fire, electrical shock and injury.

WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system if necessary.

ELECTRICAL SPECIFICATIONS

Voltage………………220 VAC/50Hz

Total Amps…………..6.5 Amps

Total Watts…………..1350 Watts

Heater Ratings………1200 Watts

SERVICE INSTRUCTIONS

WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury

REPLACING LIGHT BULBS

This fireplace uses two clear 220 Volt, 60 Watt, E-14 socket base light bulbs (small base, chandelier candle type).The 60 Watt bulbs are located under the log set/ember bed. For convenience, if one of the bulbs burns out, it may be a good

idea to replace both of the light bulbs.

1.Turn off power to the unit by unplugging the power cord.

2.Let fireplace cool if it has been operating.

3.Remove the two fixing self-tapping screws on the screen. Pull the screen upward a little bit, and then out.

4.Remove the two screws that secure the log set in position.

5.Examine the bulbs to determine which bulbs need to be replaced.

6.While holding the socket, unscrew the defective bulb (s).

7.Install the new light bulb(s) by holding the socket and screwing them.

8.Reinstall the log set and screen. Follow the above procedure in reverse order.

9.The diameter of the pilot light bulb is 5mm. If the pilot light bulb need to be replaced, follow steps 1,2,3,4 above. Then use the pilot light bulb socket w/wiring assembly replace the primary pilot part, and connect wires according to primary connection . Then follow step 8 above.

WARNING: Do not exceed 60 Watts per bulb. Use of higher rated bulbs may result in a fire causing property damage and personal injury.

4

Image 4
Contents For Your Safety Important instructions ……………………………………………………………3 General Electrical Specifications Clearance to CombustiblesElectrical Connection Replacing Light BulbsMaintenance of Motors Glass InformationMain ON/OFF Switch Heater ON/OFF SwitchInstructions for Power Heater Thermostat ControlSpecifications Model V50TYLA-C Model V50TYLA-OV50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC V50TYLA-O Item# Part Descripition Part NumberV50TYLA-C Item# Part Descripition Part NumberV50TYLA-DO Item# Part Descripition Part NumberV50TYLA-BC V50TYLAR-BC

V50TYLA-C, V50TYLA-O, V50TYLA-DO, V50TYLA-BC, V50TYLAR-BC specifications

The Procom V50TYLA series represents a remarkable line of advanced equipment tailored for diverse applications across various industries. The series includes models V50TYLA-BC, V50TYLA-DO, V50TYLA-C, V50TYLA-O, and V50TYLAR-BC, each designed with unique features and cutting-edge technologies that enhance performance, reliability, and user experience.

One of the main features of the V50TYLA series is its superior energy efficiency. Each model is equipped with state-of-the-art energy management systems that optimize power consumption without compromising performance. This energy efficiency is not only environmentally friendly but also reduces operational costs, making it an attractive option for businesses looking to improve their bottom line.

The V50TYLA-BC and V50TYLA-DO models incorporate advanced digital communication technologies, allowing for seamless integration with other systems. This feature enables real-time monitoring and control, which is crucial for industries that rely on constant data flow and operational oversight. The intuitive interfaces provided in these models facilitate easy navigation and management, catering to both experienced operators and those new to the technology.

For applications that demand robustness and durability, the V50TYLA-C and V50TYLA-O models stand out. They are constructed with high-quality materials designed to withstand extreme conditions, ensuring longevity and consistent performance even in challenging environments. Enhanced protective features, such as weather resistance and impact protection, make these models suitable for outdoor installations and harsh industrial settings.

The V50TYLAR-BC model further elevates the series with its innovative design focused on user-centric features. This model boasts enhanced customizability, allowing users to tailor functionalities and performance specifications according to their specific needs. Additionally, the system’s compatibility with various peripherals expands its versatility, making it an ideal choice for businesses with diverse operational requirements.

Overall, the Procom V50TYLA series is characterized by its commitment to performance, energy efficiency, and adaptability. With a blend of cutting-edge technology and robust design, each model within the series offers unique benefits, catering to the specific needs of various industries. Whether it’s for communication, durability, or customizability, the V50TYLA series stands as a preferred choice for modern enterprises seeking reliable and efficient solutions.