LCD WITH BUILT-IN DVR USER MANUAL
3.3.5 Housing setting
Moving cursor upon [Pan/Tilt setting] and pressing [ENTER] key can enter into quad channel Pan/Tilt port setting interface
A. Channel: Denotes system's channel number.
B. Protocol: Denotes the communication protocol between system and decoder. Moving cursor to this selection item and pressing [ENTER] key can make selection among different protocol (Pe1co-D/P/09-15/Dscp/FastDome/PIH1016-1017/JECFastD/RM110/Neocam) Select ed protocol must match to the protocol of decoder, only can it control front equipment correctly.
C. Baud rate: Denotes communication speed between system and decoder. Moving cursor to this item selection and pressing [ENTER] key can make selection among different baud rate (1200/2400/4800/9600), selected baud rate must match decoder's baud rate, only can it control front equipment correctly.
D. Pan/Tilt code: Moving cursor upon this selection item and pressing [ENTER] can make selection among different Pan/Tilt serial number (01-63), system's 01 code number match
to decoder's first address code, that is address code "01"
E. After setting up all item selection, move cursor to [RETURN] and press [ENTER] key will return toprevious menu, and save Pan/Tilt parameter setting.
Attention: Pan/Tilt protocol, baud rate, Pan/Tilt serial number three item s must be in accordance with outer Pan/Tilt (quick ball) setting parameter.
Pan /Tilt operation: After setting Pan/Tilt parameter correctly, press [F2] key on remote
control under single monitoring state, the top left corner of screen will display "Pan/Tilt control" character, temporarily, we can operate this channel's Pan/Tilt by using press [F2] key on remote control and panel.
【
】、【
】Key: Lens up and down motion, display character: up and down;
【
】、【
】Key: Lens left and right motion, display character: Pan/Tilt left and right;
【Change times +】、【Change time -】Key: Adjust image far and near extent, display character: Change times + and change tim es -;
【Aperture +】、【Aperture -】Key: Adjust image bright and dark extent, display character: Aperture + and aperture -;
【Focus +】、【Focus -】Key: Adjust image clarity extent, display character: Focus + and focus -;
【Automatic】Key: signifies automatic control, display character: Automatic
【Transfer】Key: Pan/Tilt transfer c ontrol, display character: transfer 00, back key;
【Pre-set】Key: Pan/Tilt preset control, display c haracter: preset 00, back key.
【Washer switch/Light】Key : Washer switch and light assistant switch control, display charact er: Washer switch;
Pressing [F2] and [Pan/Tilt] once more will exit Pan/Tilt operation, and return to single image monitoring state; Switch monitoring image and pressing [F2] key can enter into another channel Pan/Tilt operation.
Warning 1: When operating Pan/Tilt function, system can't startup manual video recording function.
Warning 2: When operating Pan/Tilt function, once system startup video record (timing or alarm startup), temporarily can't affect Pan/Tilt operation.
Troubleshooting: When Pan/Tilt doesn't operate normally, Please check RS-485 (see "Alarm Port lead line definition") and Pan/Tilt parameter
-e15-
LCD WITH BUILT-IN DVR USER MANUAL
3. 1.2 Remote Control Unit
L O GIN/ L OCK | PO WE R ON |
PL AYBA C K | | | |
QUAD | 1 | 2 | 3 |
| | |
| 4 | 5 | 6 |
P A RAMET E R | | | |
ANAL O G | 7 | 8 | 9 |
| + | |
| | 0 |
ZOOM + | | | ZO OM- |
FO CUS+ | FO CUS- |
| EXIT | |
AU TO | REC ALL | P R ESET | SW ITC H |
PLAY | SLOW | | CF |
F WD | REV | | NET |
R ECOR D | ST OP | SE T UP |
F1 | F 2 | F3 | F4 |
Buttons on Remote Control Unit and their functions:
①Digital Buttons Area
【0-9】Button：Digital butt ons，used for using digit input or video switc h，when under the built-in quad state, press 1、2、3、4 digit buttons mean to switch the picture output to the first, second, third and forth channel video single picture；
【+】、【-】Button：Adjusting various parameters；
②Menu Operating Buttons Area
： UP Directional button;
：DOWN Directional button;
： LEFT Directional button;
：RIGHT Directional button;
【ENTER】button：for confirmation，choosing the menu items, and press this butt on to enter into the selected sub-menu；Pressing this button can display the real time of the system when playing back the recording；
③Platform control function buttons
【ZOOM+】、【ZOOM-】Button：Adjust the distance of the picture；
【APERTURE+】、【APERTURE-】Button：Adjust the brightness of the pictur e；
【FOCUS+】、【FOCUS-】Button：Adjust the sharpness of the picture；
【AUTO】Button： Control automatically；
【RECALL】Button： standby button in control of platform；
【PRESET】Button： Preset control on platform, standby button；
【SWITCH】Button： control on some assistant switch；
④Play function buttons
【PLAY】Button：Play the the recording on the hard drive；
【SLOW】Button：Play the images slowly，at speed of ×1/2、×1/4、×1/8 time s，or press 【play】button to return to normal playing speed；
【PAUSE/SETP】Button：Press one time to Pause the picture ,and then press continuously, picture will be displayed frame by frame, press【Play】button to return to normal speed of playing.
【FWD】Button：Play fast forward of the playback picture，at the speed of×2、×4 times，press 【Play】Button to return to t he normal speed of playing；
【REV】Button：Play fast backward of the playback pictures， at speed of×2、×4 times，press 【Play】Button to return the normal speed of playing；
-e8-
