Marley Engineered Products MCM1503A manual Limited Warranty, Features, To Operate, Cleaning & Care

FEATURES

•Tip-Over Switch - shuts heater off automatically if unit tips over.

•Pilot Light - glows when heater is plugged in.

•Manual Reset Over-Temperature Safety Cutoff - auto- matically turns heater off if overheating occurs.

Model MCM 1503A

This heater is provided with a grounded (3 blade) plug for use on 110-120 volts AC.

CAUTION: The grounded plug must be used with a grounded outlet. Do not use an adapter in a 2-slot wall outlet unless the ground lug of the adapter is properly con- nected to a known building ground. Failure to use heater with properly grounded outlet or adapter could result in an electric shock hazard. The adapter should not be used if a 3 slot grounded receptacle is available.

TO OPERATE

1.Plug the heater power cord directly into a standard grounded 110-120 volt AC outlet. Always operate the heater in the upright position with the rubber feet on the

floor.

CAUTION: Be sure plug fits tightly into outlet. A loose fit will cause overheating and damage to the plug. Plug may feel warm during normal usage.

2.Rotate heat selection knob to “LOW” (600W), “MED” (900W) or HIGH (1500W) setting.

3.Rotate the “THERMOSTAT” knob clockwise (right)until the knob stops. The heater should begin heating. At “LOW” (600W) the fan will not operate. At “MED”

(900W) and “HIGH” (1500W) settings, the fan should start to blow warm air.

4.Allow the heater to operate until the room temperature reaches the desired level, then slowly rotate the “THERMOSTAT” knob counter-clockwise (left) until the heater cycles off. At this setting, the heater will cycle on and off automatically to maintain this comfort level.

NOTE: Do not force knob beyond its normal stop position. It may be necessary to make minor adjustments to the thermostat to maintain the desired comfort level. Clockwise movement will increase the room temperature. Counter-clockwise movement will decrease room temperature.

5.To conserve energy, the heater may be operated at a lower wattage by placing the heat selection knob at the “LOW” (600W) or MED (900W) settings.

6.When heater is not needed, rotate control knob to the “OFF” position, remove the plug from outlet, and move heater to safe place for storage.

CLEANING & CARE

Your heater is designed for trouble-free operation with little maintenance. However, routine cleaning is recommended as follows:

1.Before attempting to clean heater, turn heater to “OFF” position and remove plug from outlet.

2.Using damp cloth, wipe dust and dirt from heater to cabinet. Do not use waxes as they may discolor.

3.When heater is not to be used for an extended time, turn to “OFF” position, unplug from outlet and place heater in safe place, such as a box, to prevent possible damage.

TO RESET OVER-TEMPERATURE CONTROL This heater is equipped with a built-inover-temperature safety switch that will cycle the heater off if the heater overheats. After heater is allowed to cool and the condition that caused the overheating is corrected, using a small straight object, such as a pencil, push in button located inside small hole on side of heater marked “RESET”.

LIMITED WARRANTY

All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for two years from date of pur- chase. This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; not to equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for war- ranty work must be accompanied by proof of the date of installation.

The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley.

It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.

THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARISING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When requesting return authorization, include all catalog numbers shown on the products.

NEED TECHNICAL OR WARRANTY ASSISTANCE?		5200-2455-000	PPD 029
	PLEASE CALL TOLL-FREE 1-800-642-HEAT.		6/99
2
	SAVE THESE IMPORTANT INSTRUCTIONS

SPX Corporation

470 Beauty Spot Rd. East

Bennettsville, SC 29512 USA