Vermont Casting 2478CE Securing the Connector to a Masonry Chimney, Freestanding Installations

Page 7

Securing the Connector to a Masonry Chimney

The Dutchwest Convection heater may be connected to either a freestanding masonry chimney or a masonry fireplace chimney.

Freestanding Installations

If the chimney connector must pass through a combus- tible wall to reach the chimney, follow the recommenda- tions in the wall pass-through section that follows.

The opening through the chimney wall to the flue (the “breech”) must be lined with either a ceramic or metal cylinder, called the “thimble”, which is securely cemented in place. (Fig. 6) Most chimney breeches incorporate thimbles, but check to be sure the fit is snug and the joint between thimble and chimney wall firmly cemented.

 

Thimble

 

Sleeve

 

Flue

Elbow

Thimble

 

Keep

 

Sleeve

 

End Flush

 

with Flue

 

Tile

Chimney

Connector

Flue Liner

ST243

Fig. 6 The thimble, made of either ceramic or metal, must be cemented in place securely.

A special piece called the “thimble sleeve,” slightly smaller in diameter than the standard connector and most thimbles, will ease the removal of the chimney connector system for inspection and cleaning. Thimble sleeves should be available from your local dealer.

To install a thimble sleeve, slide it into the breech until it is flush with the inner flue wall. Don’t extend it into the actual flue passage, as that could interfere with the draft.

The thimble sleeve should protrude 25-51 mm (1-2”) into the room. Use furnace cement and thin gasketing to seal the sleeve in place in the thimble. Secure the chimney connector to the outer end of the sleeve with sheet metal screws.

Fireplace Installations -

Above the Fireplace

In this installation, the chimney connector rises from the stove, turns ninety degrees, and goes back into the fireplace chimney. The liner of the fireplace chimney should extend at least to the point at which the chimney

Dutchwest Non-Catalytic Convection Heater

connector enters the chimney. Follow all the guidelines for installing a chimney connector into a freestanding masonry chimney, and pay special attention to these additional points:

•Check the stove and chimney connector clearances to combustible mantel or trim materials. Use the necessary combination of mantel, trim, and connec- tor heat shields to provide the required clearances. (Fig. 7)

•Double-check connector clearance from the ceiling.

•The fireplace damper must be closed and sealed to prevent room air from being drawn up the flue, reducing the draft. However, it must be possible to re-open the damper to inspect or clean the chimney.

Masonry Wall

Ceramic Flue Liner

Chimney Connec- tor Shield

Block-Off Plate

Chimney Connector

ST796as

Fig. 7 The connector enters flue above the fireplace. If the clearance between the chimney connector and either the mantel and/or the ceiling is inadequate, special protective shields will be required.

Fireplace Installations -

Through the Fireplace

The Convection heater may be installed either without legs* as a fireplace insert, or with standard legs at- tached - depending on the safety regulations that apply to your situation, the height of the fireplace opening and your own preference. For either situation, the chimney connector/positive connection kit extends back from the stove, enters the fireplace cavity, and turns upward. It then passes through the fireplace damper opening and smoke chamber and connects to the chimney flue.

In such installations, a “positive connection” must be made to the chimney flue with a special kit available from your local dealer. Also, special clearance and floor protection provisions must be observed. These provi- sions are discussed in the Clearance and Floor Protec- tion sections respectively.

30003850

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Non-Catalytic Convection Heater Model 2478CE Accessories Table of ContentsDutchwest NC Model 2478CE SpecificationsChimney Types InstallationMasonry Chimneys Chimney Size Guidelines for Installing the Chimney ConnectorTwo Types of Connector Prefabricated ChimneysSecuring the Connector to a Prefabricated Chimney Single-Wall ConnectorDouble-Wall Connector Assembling Single-Wall Chimney ConnectorFireplace Installations Through the Fireplace Securing the Connector to a Masonry ChimneyFreestanding Installations Fireplace Installations Above the FireplaceHearths Wall Pass-ThroughsFloor Protection for Fireplace Installations Fireplace InstallationsKeep the Stove a Safe Distance From Surrounding Materials Clearances Connecting Flue Pipe ClearancesUnpack the Parts AssemblyAttach the Legs and Heat Shield Fan Kit Installation Operation Heater Controls and Features Air ControlBurn Only High-Quality Fuel Damper Function Successful Wood BurningLoad Doors How to Build and Maintain a Wood Fire Loading Wood Use the Air Control Settings That Work Best for YouBreak-in Fires Reloading and Reviving the Fire Lighting the FireSafe Ash Handling Remove Ashes FrequentlyTest and Repair the Door Gaskets MaintenanceCleaning the Glass Adjust the Door LatchPrimary Air Control Adjustment Damper AdjustmentAvoid Damaging the Glass Door Panel Stove Cleaning the Chimney SystemInspect Regularly, Clean As Required Maintenance ScheduleMasonry Chimney Draft ManagementPipe & Chimney Layout Steel ChimneyIndoor/ Outdoor Location Flue SizingNegative Pressure Draft TestingCreosote BackpuffingDutchwest Convection Heater Dutchwest Convection Heater Dutchwest Non-Catalytic Convection Heater Limited Lifetime Warranty Mhsc

2478CE specifications

Vermont Castings 2478CE is a premier wood stove that exemplifies the perfect blend of traditional craftsmanship and modern efficiency. Designed for those who appreciate both aesthetic and functional qualities in home heating, this model is a standout in the Vermont Castings lineup.

One of the main features of the 2478CE is its impressive heating capacity. It can produce up to 75,000 BTUs, making it capable of warming spaces of up to 2,500 square feet. This robust output ensures that your home remains cozy even on the coldest winter nights, allowing for a warm and inviting atmosphere.

The stove is constructed from high-quality cast iron, which not only adds to its durability but also allows for superior heat retention. This means that the stove will continue to emit warmth long after the fire has burned down, providing extended comfort without the need for constant refueling.

Vermont Castings has equipped the 2478CE with advanced air management technology. The unique air wash system ensures a clean and efficient burn by directing air across the glass door. This feature keeps the viewing window clear, allowing users to enjoy the mesmerizing flames without the nuisance of soot buildup.

Moreover, the 2478CE utilizes secondary combustion technology, which helps to maximize efficiency and minimize emissions. This innovative system re-burns smoke and gases that would otherwise be released into the atmosphere, ensuring that more heat is extracted from the wood. As a result, the stove achieves an impressive efficiency rating of up to 82%.

Another notable characteristic of the Vermont Castings 2478CE is its traditional design, complete with intricate detailing and a large firebox. The firebox is designed to accommodate larger logs, allowing for longer burn times and reduced frequency of refueling. Additionally, the stove is available in various finishes to match any home decor style, from classic black to vibrant enamel colors.

For those looking to enhance their hearth experience, the 2478CE can be paired with a variety of optional accessories, such as a classic heat shield or a blower, further improving its performance and efficiency.

In conclusion, the Vermont Castings 2478CE represents an excellent choice for homeowners seeking a reliable, beautiful, and efficient wood stove. With its substantial heating capacity, advanced technologies, and timeless design, it promises to be a centerpiece of comfort in any home for years to come.
Top Page Image Contents