Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

•Do not cover or obstruct top and bottom air vents of the heater.

•Read all instructions before using this heater.

•This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

•Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.

•Extreme caution is necessary when any heater is used by or near children or handicapped persons.

•This heater is equipped with a grounded type plug (see illustration)

and must be pluged into a grounded type outlet as shown. This is a safety feature: DO NOT REPLACE THIS PLUG!

•Always inspect power cord, and do not operate heater with a damaged cord or plug.

•DO NOT OPEN HEATER. There are no user serviceable parts inside.

•Do not use the heater if the cord or plug is damaged, or if the heater has malfunctioned, or if it has been damaged or dropped in any way. In such a case, return the heater to an authorized service facility for examination and/or repair.

•Do not use outdoors – for indoor use only.

•This heater is not intended for use in bathrooms, laundry areas, wet areas or similar indoors areas.

•Never locate heater where it may fall into a bathtub or other water containers.

•Do not run the heater cord under carpeting, or otherwise cover the cord. Make sure the cord is out of the way so that it does not pose a risk of tripping.

•Turn off heater before unplugging from the electrical outlet.

•Do not insert objects through the air vents of the heater as this may cause an electric shock or fire. To prevent fire do not block air intakes or exhaust in any manner.

•A heater has hot and arcing parts inside. Never use the heater in the vicinity where paint thinners, gasoline, paint or other flammable liquids are used or stored.

•Use this heater only as described in this manual.

Any other use may cause injury to persons, or property damage, or electric shock.

•Avoid using an extension cord to power the heater because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be of a No. 14 AWG minimum size, and should be rated no less than 1875 watts.

•This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that is already being used to power other appliances.

•While it is normal for the heater’s plug to feel warm to the touch, a loose fit between the plug and the electrical outlet may cause overheating and warping of the plug. If the outlet is loose, contact a qualified electrician to replace loose or worn outlets.

•Do not allow water to splash on the heater. If the heater appears to be damp, discontinue its use immediately.

•The output of this heater may vary and its temperature may become intense enough to burn exposed skin.

Use of this heater is not recommended for persons with reduced sensitivity to heat or inability to react to avoid burns.

•Service of the heater other than cleaning should be performed by an authorized service center. No user serviceable parts inside. Only authorized service personnel shall handle repair work.

•The appliance has an internal over-temperature safety device, which automatically switches the heater off, if an over-heat situation is detected. Manually reset the unit once the heater cools off.

•When the unit cools off, if you notice the safety device still switches off the heater, unplug the unit, wait 30 seconds to a minute, and plug in again. This will trigger the unit and it will switch on.

AMH9 specifications

Amcor AMH9 is a state-of-the-art packaging solution that has garnered attention for its advanced features and technologies. Designed for a variety of applications, the AMH9 can handle both flexible and rigid packaging demands, making it a versatile choice for manufacturers across numerous industries. This machine symbolizes the commitment of Amcor, a global leader in packaging solutions, to innovation and sustainability.

One of the main features of the Amcor AMH9 is its high-speed production capability. It can achieve impressive output rates, often exceeding industry standards. This efficiency is crucial for manufacturers looking to boost productivity and reduce operation costs. The machine's automation enables seamless transitions between different packaging formats, minimizing downtime and maximizing throughput.

Another notable characteristic of the AMH9 is its advanced sealing technology. This feature ensures that every package is securely sealed, enhancing the shelf life of the product while preventing contamination. The sealing process is optimized for various materials, which allows the AMH9 to cater to different product requirements without compromising quality.

In terms of technology, the AMH9 incorporates user-friendly interfaces and smart monitoring systems. These advancements enable operators to easily adjust settings, continuously oversee production, and quickly troubleshoot any issues. The machine's connectivity allows for real-time data analysis, which facilitates improvements in efficiency and overall performance.

Sustainability is at the forefront of Amcor's design philosophy, and the AMH9 reflects this commitment. It is capable of using eco-friendly materials that prioritize recyclability and reduce environmental impact. This aligns with growing consumer demand for sustainable packaging solutions, making the AMH9 an attractive option for brands dedicated to reducing their carbon footprint.

The AMH9 also stands out with its multi-format capability, allowing it to produce a wide range of packaging types, such as pouches, bags, and trays. This flexibility caters to diverse market needs while simplifying the supply chain for manufacturers.

In summary, the Amcor AMH9 is a cutting-edge packaging machine that offers high-speed production, advanced sealing technology, user-friendly interfaces, and a commitment to sustainability. Its multi-format capabilities make it an essential tool for manufacturers aiming to enhance their operational efficiency while responding to evolving market trends.