
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
T R O U B L E S H O O T I N G
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1. | Read all instructions before using this heater. |
2. | This heater is hot when in use. To avoid burns, do not |
| let bare skin touch hot surfaces. If provided, use |
| handles when moving this heater. Keep combustible |
| materials, such as furniture, pillows, bedding, papers, |
| clothes, and curtains at least 3 feet (0.9 m) from the |
| front of the heater and keep them away from the |
| sides and rear. |
3. | Extreme caution is necessary when any heater is |
| used by or near children or invalids and whenever |
| the heater is left operating and unattended. |
4. | Always unplug heater when not in use. |
5. | Do not operate any heater with a damaged cord or |
| plug or after the heater malfunctions, has been |
11. | To prevent a possible fire, do not block air intakes or |
| exhaust in any manner. Do not use on soft surfaces, |
| like a bed, where openings may become blocked. |
12. | A heater has hot and arcing or sparking parts inside. |
| Do not use it in areas where gasoline, paint, or |
| flammable liquids are used or stored. |
13. | Use this heater only as described in this manual. Any |
| other use not recommended by the manufacturer |
| may cause fire, electric shock, or injury to persons. |
14. | Always plug heaters directly into a wall outlet/ |
| receptacle. Never use with an extension cord or |
| relocatable power tap (outlet/power strip). |
15. | When unplugging, be sure to pull by the plug and |
| not the cord. |
16. | If the heater will not operate, see specific instructions |
| on Auto Safety |
17. | DO NOT attempt to repair or adjust any electrical or |
TECHNICAL SPECIFICATIONS
•Amps: 12.5
•Wattage: 1500W (+5%
•Working Voltage: 120V AC/60 Hz
OPERATING INSTRUCTIONS
1.Carefully remove your heater from the box. (Please save the carton for
2.Place heater on firm level surface.
3.Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps.
4.Plug the heater into a 120V AC electrical outlet.
1TOUCH® HEATER THERMOSTAT
your desired temperature is set in either Max or Low setting. The selected Temperature Indicator Light will illuminate. When the ambient temperature rises above the set temperature, the heater will stop. When the ambient temperature drops below the set temperature, the heater will turn on automatically.
NOTE: There will be temperature variance measured at the internal sensor, when the ambient temperature drops below the set temperature, it may take a longer time for the internal sensor to cool down, and then
NOTE: When the 1Touch® heater thermostat is set, either the Max or Low Indicator light, or the preset Temperature Indicator Light will remain lit during operation. (See Figure 1)
CLEANING/MAINTENANCE
Always unplug the heater before cleaning and allow the heater to cool down.
1.Clean the unit with a soft cloth moistened with a mild soap solution.
2.NEVER use abrasive or flammable solvents to clean the unit.
3.After cleaning, be sure to completely dry the unit with a cloth or towel.
4.Store heater in a cool, dry location.
5.It is recommended that you store the unit in its original carton.
TIP: Over time, dust may accumulate on the front grills. This can be removed by wiping the unit with a damp cloth.
TROUBLESHOOTING
If your heater fails to operate:
•Make sure the electrical outlet and circuit breaker are working.
•Check for obstructions. If you find an obstruction, turn OFF and UNPLUG the heater. Carefully remove the obstruction and follow the reset instructions.
•The thermostat might be set too low. Press the Mode
Button (
/Mode) until the heater restarts.
Please DO NOT attempt to open or repair the heater.
If you have any questions regarding your product or would like to learn more about other Holmes® products, please visit our website at www.holmesproducts.com.
| dropped or damaged in any manner. Discard heater, |
| or return to authorized service facility for |
| examination and/or repair. |
6. | Do not use outdoors. |
7. | This heater is not intended for use in bathrooms, |
| laundry areas and similar indoor locations. Never |
| locate heater where it may fall into a bathtub or |
| other water container. |
8. | Do not run cord under carpeting. Do not cover cord |
| with throw rugs, runners, or similar coverings. Do not |
| route cord under furniture or appliances. Arrange |
| cord away from traffic area and where it will not be |
| tripped over. |
9. | To disconnect heater, turn controls to off, then |
| remove plug from outlet. |
10. | Do not insert or allow foreign objects to enter any |
| ventilation or exhaust opening as this may cause an |
| electric shock or fire, or damage the heater. |
mechanical functions on this unit. Doing so will void |
your warranty. The inside of the unit contains no user |
serviceable parts. All servicing should be performed |
by qualified personnel only. |
18. Discontinue use if plug or outlet is hot. It is |
recommended that the outlet be replaced if plug or |
outlet is hot to touch. |
19. The heater must not be located immediately below a |
immediate surroundings of a bath, a shower or a |
swimming pool. |
SAVE THESE
INSTRUCTIONS
INSTRUCTIONS
Your heater is equipped with a technologically advanced 1Touch® heater's electronic thermostat. You can set the heater to run continuously in manual mode or set the thermostat to your desired temperature setting. The thermostat will automatically turn the heater ON or OFF depending on the preset comfort level. The comfort level ranges between 60° and 80° Fahrenheit. Press the Mode Button (/Mode) to select your desired comfort level:
1. Max - Manual HIGH
Press the Mode Button ( /Mode) once to set the heater at Max manual setting. The Max Indicator Light will illuminate. The heater will run continuously at HIGH setting.
2. Low - Manual LOW
Press the Mode Button ( /Mode) again to set the heater at Low manual setting. The Low Indicator Light will illuminate. The heater will run continuously at reduced wattage.
NOTE: It is normal for the heater to cycle ON and OFF as it maintains the set temperature. To prevent the unit from cycling, you need to raise the thermostat setting.
NOTE: 1Touch® heater has memory. The 1Touch® heater's thermostat will remember the previous temperature setting after the unit has been turned off. However, if the unit is unplugged, or the unit is turned off, the 1Touch® heater thermostat will be reset and will no longer remember the previous setting.
Figure 1 | Temperature Indicator Lights | ||||
Mode Button | |||||
| |||||
( |
|
| /Mode) |
| |
|
|
|
AUTO SAFETY SHUT-OFF
This heater is equipped with a patented, technologically advanced, safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit.
RESET INSTRUCTIONS
If your heater shuts down:
1)Unplug the unit and wait 30 minutes.
2)Plug in and operate normally.
NOTE: To shut unit OFF, hold Mode Button ( /Mode) down for 2 seconds.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
NOTE: To shut unit off at any time, press and hold the Mode Button ( /Mode) for 2 seconds or keep pressing the Mode Button (
/Mode) until all temperature indicators go OFF.
3. Preset Temperature Levels (60 °F - 80 °F)
Continue to press the Mode Button ( /Mode) to cycle through the Temperature Indicators (60 °F - 80 °F) until
Max/Low Indicator Lights
L E A Y C O N S E RV E E S TA S I N S T R U C C I O N E S
I M P O R TA N T E S D E S E G U R I D A D
C A R A C T E R Í S T I C A S Y O P E R A C I O N E S
L I M P I E Z A / M A N T E N I M I E N T O D I A G N O S T I C O D E P R O B L E M A S
Para reducir el riesgo de incendios, descargas eléctricas y lesiones personales al utilizar electrodomésticos, siga siempre las precauciones básicas de seguridad, incluyendo las que se mencionan a continuación:
1. | Lea todas las instrucciones antes de usar este calefactor. |
2. | El calefactor se calienta al usarlo. Para evitar |
| quemaduras, NO toque las superficies calientes con la |
| piel. Si existen, utilice las manijas para mover la |
| unidad. Mantenga los materiales combustibles, como |
| muebles, almohadones, sábanas, papeles, ropa y |
| cortinas a por lo menos 3 pies (0,9m) de la parte |
| delantera del calefactor y manténgalos alejados de |
| los costados y de la parte de atrás. |
3. | Debe tener mucho cuidado cuando el calefactor es |
| utilizado por, o cerca de niños o inválidos, y siempre |
| que se deje el calefactor prendido y desatendido. |
4. | Siempre desenchufe el calefactor cuando no lo utilice. |
5. | NO utilice el calefactor si el cable o el enchufe están |
| dañados o luego de una falla, se haya caído o haya |
| sufrido cualquier tipo de daño. Deseche el calefactor |
| o devuélvalo al centro de servicio autorizado para su |
causar un choque eléctrico o incendio, o dañar el calefactor.
11. | Para evitar un posible incendio, no bloquee las |
| entradas de aire o escape de ninguna manera. No lo |
| use en superficies blandas, como una cama, donde |
| las aberturas se pueden bloquear. |
12. | Un calefactor tiene partes calientes y que pueden |
| producir chispas en su interior. NO lo utilice en áreas |
| donde se utiliza o se guarda gasolina, pintura o |
| líquidos inflamables. |
13. | Utilice este calefactor sólo como se describe en este |
| manual. Cualquier otro uso no recomendado por el |
| fabricante puede provocar incendios, descargas |
| eléctricas o lesiones a personas. |
14. | Siempre conecte el calefactor directamente a un |
| tomacorriente de pared. Nunca lo use con un cable |
| de extensión o con un tomacorriente múltiple. |
15. | Al desenchufarlo, asegúrese de tirar del enchufe y no |
| del cable. |
16. | Si el calefactor no funciona, vea las instrucciones |
| específicas del apagado automático de seguridad. |
ESPECIFICACIONES TÉCNICAS
•Amperes: 12.5
•Potencia: 1500 Vatios (+5%
•Voltaje de funcionamiento: 120V CA/60 Hz
INSTRUCCIONES DE USO
1.Saque cuidadosamente el calefactor de la caja. (Conserve la caja para guardarlo en el verano).
2.Coloque el calefactor en una superficie firma y nivelada.
3.Evite sobrecargar el circuito eléctrico evitando utilizar otro artefacto de alta potencia en el mismo tomacorriente. A 1500 Vatios, esta unidad consume 12,5 Amperes.
4.Enchufe el calefactor en un tomacorriente de 120V CA.
INSTRUCCIONES DEL TERMOSTATO ELECTRÓNICO PARA EL CALEFACTOR 1TOUCH®
3.Predetermine los niveles de temperatura [60 °F a 80 °F])
Continúe presionando el botón de modo/apagado ( / Modo) para alternar entre los indicadores de temperatura [60 °F a 80 °F]) hasta establecer la temperatura deseada en Max o Low. El indicador luminoso de la temperatura establecida se encenderá. Cuando la temperatura ambiente supere la temperatura establecida, el calefactor se apagará. Cuando la temperatura ambiente disminuya por debajo de la temperatura establecida, el calefactor se encenderá automáticamente.
NOTA: Existirá variación de temperatura, que se mide en el sensor interno, cuando la temperatura ambiente desciende por debajo de la temperatura establecida. Es posible que el sensor interno tarde más en enfriar y, luego, reactivar el calefactor para que vuelva a encender. Si la temperatura ambiente es demasiado baja, eleve el nivel de temperatura establecida o seleccione la configuración Max/Low para que el calor sea constante.
NOTA: Cuando el termostato del calefactor 1Touch® está programado en la luz de potencia ALTA (Max) o BAJA
haber apagado la unidad. Sin embargo, si se desenchufa la unidad, no recordará las programaciones de las temperaturas anteriores.
LIMPIEZA / MANTENIMIENTO
Siempre desenchufe el calefactor y deje que se enfríe antes de limpiarlo.
1.Limpie la unidad con un paño suave, humedecido en una solución de jabón suave.
2.NUNCA utilice solventes abrasivos o inflamables para limpiar la unidad.
3.Luego de limpiarla, asegúrese de secar completamente la unidad con un trapo o toalla.
4.Guarde el calefactor en un lugar fresco y seco.
5.Se recomienda guardar la unidad en su embalaje original.
*CONSEJO: Con el transcurso del tiempo se acumulará polvo en las rejillas delanteras que puede eliminarse con un paño húmedo.
DIAGNÓSTICO DE PROBLEMAS
Si su calefactor no funciona:
•Asegúrese de que el tomacorriente y llave térmica funcionen correctamente.
•Verifique que no haya ninguna obstrucción. Si encuentra una obstrucción, apague el calefactor, y DESENCHUFELO. Quite cuidadosamente la obstrucción y siga el procedimiento para volver a funcionar la unidad.
•El termostato puede estar ajustado demasiado bajo.
Presione el botón de modo ( /Modo) hasta que la unidad se vuelva a encender.
NO intente abrir o reparar el calefactor.
Si tiene preguntas relacionadas con este producto o si está interesado en conocer otros productos Holmes®, póngase visite nuestro sitio web www.holmesproducts.com.
| revisión y/o reparación. |
6. | NO utilizar en el exterior. |
7. | Este calefactor no está diseñado para ser utilizado en |
| baños, lavaderos y zonas similares de interiores. |
| NUNCA coloque el calefactor donde pueda caerse |
| dentro de una bañera u otro recipiente con agua. |
8. | No coloque el cable debajo de la alfombra. No cubra |
| el cable con alfombras, tapetes o artículos similares. |
| No pase el cable por debajo de muebles o |
| electrodomésticos. Coloque el cable lejos del área de |
| tráfico y donde no se tropiece con él. |
9. | Para desconectarlo, gire el control a la posición OFF, |
| luego quite el enchufe del tomacorriente. |
10. | No inserte ni permita que objetos extraños penetren |
| en la ventilación o salida de aire ya que esto puede |
17. | NO intente reparar o ajustar ninguna función |
| eléctrica o mecánica de esta unidad. El hacerlo |
| invalidará la garantía. La unidad no contiene partes |
| reparables por el usuario. Toda reparación debe ser |
| realizada únicamente por personal calificado. |
18. | Deje de usarlo si el cable o el enchufe se calienta. Se |
| recomienda que reemplace el tomacorriente si el |
| enchufe o el tomacorriente se calienta. |
19. | El calefactor no se debe localizar inmediatamente |
| debajo de un tomacorriente. No use este calefactor en |
| áreas cercanas a un baño, una ducha o una piscina. |
CONSERVE ESTAS
INSTRUCCIONES
Su calefactor cuenta con un avanzado termostato electrónico del calefactor 1Touch®. Usted puede ajustar el calefactor para que funcione constantemente en modo manual o puede ajustar el termostato al nivel de temperatura deseado. El termostato encenderá y apagará automáticamente el calefactor dependiendo del nivel de temperatura previamente ajustado. El nivel de temperatura confortable se encuentra entre 60° y 80° Fahrenheit. Para seleccionar el nivel de comodidad deseado, pulse el botón de modo/apagado (/Modo):
1. Max - ALTO manual
Para configurar el calefactor en el nivel Max manual, pulse el botón de modo/apagado ( /Modo) una vez. El indicador luminoso Max se encenderá. El calefactor funcionará continuamente en la configuración ALTO.
2.Low - BAJO manual
(Low), la luz de la temperatura programada continuará prendida durante su funcionamiento (Ver Figura 1). NOTA: Es normal que el calefactor vaya del ciclo ON a OFF para mantener la temperatura programada. Para que la unidad no pase de ciclos, debe programar la temperatura del termostato a un nivel más alto.
NOTA: El calefactor 1Touch® tiene memoria. El termostato recordará las temperaturas previas después de
Figura 1 | Luz de temperatura | |||
Botón de Mode | ||||
| ||||
( |
| /Mode) |
| |
|
|
APAGADO AUTOMÁTICO DE SEGURIDAD
Este calefactor está equipado con un sistema de seguridad patentado, de tecnología avanzada que requiere que el usuario reinicie el calefactor en caso de un sobrecalentamiento potencial. Cuando se alcanza una temperatura de un posible recalentamiento, el sistema apagará automáticamente el calefactor. Volverá a funcionar únicamente cuando el usuario prenda de nuevo la unidad.
INSTRUCCIONES VOLVER A ENCENDER
Si la unidad se apaga:
1)Desenchufe la unidad y espere 30 minutos.
2)Enchufela y vuélvala a operar normalmente.
NOTA: Para apagar la unidad, mantenga presionado el botón modo (/Modo) por 2 segundos.
ESTE ARTEFACTO TIENE UN ENCHUFE POLARIZADO (una de las patas es más ancha que la otra). Para reducir el riesgo de una descarga eléctrica, este enchufe entra de una sola forma en un tomacorriente polarizado. De no ser así, inviértalo, y si aún así no entra completamente, llame a un electricista calificado para que instale un tomacorriente apropiado.
NO INTENTE MODIFICAR ESTE ENCHUFE O ALTERAR ESTE
DISPOSITIVO DE SEGURIDAD DE NINGUNA FORMA.
Para configurar el calefactor en el nivel Low manual, pulse el botón de modo/apagado ( /Modo) nuevamente. El indicador luminoso LO se encenderá. El calefactor funcionará continuamente en un voltaje reducido.
NOTA: Para apagar la unidad en cualquier momento, pulse el botón de modo/apagado ( /Modo) durante 2 segundos o manténgalo presionado hasta que todos los indicadores de temperatura se APAGUEN.
Indicadores luminosos Max/Low
HFH136_13ESM1.indd 2
1/16/13 4:15 PM