Thank you for purchasing this Holmes® product. We understand the value of quality and are committed to making superior products that stand the test of time. We trust this product will exceed your expectations of quality and reliability. We hope that you enjoy this product and will consider purchasing another Holmes® product in the future. To see our full product line or if you have any questions or comments about this product, please visit our website at: www.holmesproducts.com.
When using electrical appliances, basic safety precautions should always be taken including the following:
1. | Read all instructions before using this appliance. |
2. | Use fan only for purposes described in the instruction |
| manual. |
3. | To protect against electrical shock do not immerse unit, |
| plug or cord in water or spray with liquids and plug the |
| appliance directly into a electrical outlet. |
4. | Close supervision is necessary when any appliance is |
| used by or near children. |
5. | Unplug from outlet when not in use, when moving fan |
| from one location to another, before putting on or |
| taking off parts and before cleaning. |
6. | Avoid contact with moving parts. |
12.Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
13.To disconnect, grip plug and pull from wall outlet. Never yank on cord.
14.Always use on a dry, level surface.
15.Do not operate fan until fully assembled with all parts properly in place.
16.This product is intended for household use ONLY and not for commercial or industrial applications.
17.WARNING: To reduce the risk of electrical shock and injury to persons, do not use in window.
18.WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state speed control device.
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
Figure 1 | | | | | | | A. | Lower Pole | L. | Fan Blade | |
| | | | | | | |
| | I | | J | | | B. | Glass Base | M. | Blade Screw |
| | | | | | G |
| | M | | | | C. | Base Nut | N. | Tilt-Adjustment Knob |
| | | | | |
| | | | | | |
| | | | | | | D. | Height Adjustment | O. | Front Grill | |
| | | | | | | | Knob | P. | Grill Ring | |
| | | | N | | | E. | Upper Pole | Q. | Grill Ring Screw |
| | H | | | | |
| | | | | | | F. | Base Cover | R. | Speed Control |
| | P | Q | | E | | G. | Motor Housing | S. | Oscillation Control |
| | | | | |
| L | | | | | |
O | Figure 1A | Figure 1A | D | | | | Assembly | T. | Notch on Motor Shaft |
| | | |
| | | | H. |
| K-(2) | | | | | | Rear Grill Nut | | | |
| | | R | | A | | I. | Rear Grill | | | |
| | | | | | | | | |
| H | | S | | | | J. | Motor Shaft | | | |
| | | | | | | | | |
| T | | | | | | K. | Prong | | | |
| | | | | | | | | |
| N | | B | | F | | | | | | |
| | | | | | | | | |
| | E | | | | | | | | | |
| | | | C | | | | | | | |
Figure 2 | | | Figure 3 | | | | Figure 5 | Figure 6 | Figure 7 |
| | | | | | | | Figure 6 | | | |
F | | | | | | | | I | | | |
| | | | | | | | | | |
3.Secure Motor Housing Assembly (G) to the top of the Upper Pole (E). Refer to Figure 3.
4.Remove Rear Grill Nut (H) from Motor Housing Assembly (G). Refer to Figure 4.
5.Position Rear Grill (I) over Motor Housing Assembly
(G).Refer to Figure 5 for correct positioning.
6.Secure Rear Grill (I) to Motor Housing Assembly (G) with Rear Grill Nut (H). Refer to Figure 6.
7.Slide Fan Blade (L) over Motor Shaft (J) and tighten Blade Screw (M). Refer to Figure 7 for correct positioning of Fan Blade (L) and Motor Shaft (J).
8.Snap Front Grill (O) into Grill Ring (P).
NOTE: You may have to loosen the Grill Ring Screw
(Q)to snap the Front Grill (O) into place.
OPERATING INSTRUCTIONS (SEE FIGURE 1A & 1)
Speed Control (R) =
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for your fan.
•Always unplug the fan before cleaning or disassembling.
•Be sure to clean your fan with a soft cloth moistened with a mild soap solution.
•Do not allow water to drip on or enter into the fan housing.
•Do not use gasoline, thinner, or benzene as a cleaner.
•Lightly run a vacuum cleaner nozzle over the fan grill to remove any dust or dirt that may have accumulated.
Fan Blade Cleaning Instructions
Make sure the fan is unplugged before disassembling and cleaning the fan blade. Carefully remove the front grill from the clips. Wipe the blade with a soft cloth moistened with a mild soap solution. DO NOT allow any liquid to drip into or enter the motor housing. Snap the front grill onto the fan. Make sure all parts are secured prior to operating the fan.
7. | Do not operate in the presence of explosive and/or |
| flammable fumes. |
8. | To avoid fire hazard, NEVER place the cord under rugs |
| or any parts near an open flame, cooking or other |
| heating appliance. |
9. | Do not operate any appliance with a damaged cord or |
| plug after the appliance malfunctions, or has been |
| dropped/damaged in any manner. Take it to an |
| Authorized Service Center for examination and/or |
| repair. |
10. | The use of attachments not recommended or sold by |
| the appliance manufacturer may cause hazards. |
11. | Do not use outdoors. |
ASSEMBLY INSTRUCTIONS (SEE FIGURE 1 - 8)
Assembly Time: 10-15 Minutes.
Tools Required: Phillips Head Screw Driver and Adjustable Wrench.
1.Remove the Height Adjustment Knob (D) and slide the Decorative Base Cover (F) over the top of the Upper Pole (E). Replace the Height Adjustment Knob (D). Refer to Figure 2.
2.Position the Lower Pole (A) over the opening of the base and secure with the Base Nut (C). Refer to Figure 2.
| | | | K-(2) | H | |
1 | E | | G | | | |
2 | | | | |
| | | | | |
| D | | Figure 7 | Figure 8 | Figure 8 | Figure 9 |
| | |
| | | |
| | E | | | | P |
| | | | | |
| | | L | | | I |
| | | T | J | |
| | | | | |
| A | | | | | |
B | | | | M | | |
| | | | | |
| | Figure 4 | Figure 5 | | | |
| C | H | | | O | Q |
| | | | |
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment
Loosen Tilt Adjustment Knob (N), move fan head to desired angle, and tighten Tilt Adjustment Knob (N) to lock in place.
Height Adjustment
Loosen Pole Locking Knob (D), Upper Pole (E) to desired height, and tighten Pole Locking Knob (D) to lock in place.
Oscillation Adjustment
Press, Pull Oscillation (S) = start, stop
FAN STORAGE
Your fan should be stored in the off-season in its original box. It is important to keep it in a safe, dry location.
•Store your fan in the original box or an appropriately sized box.
•Protect the fan head from dust.
This product is for use on 120 volts. The cord has a plug (A) as shown. An adapter
(C)is available for connecting three-blade grounding-type plugs to two-slot receptacles (B). The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
CAUTION: Use Only with GFCI Protected Receptacles.