Holmes HASF2120 warranty Assembly Instructions, Operating Instructions, Adjustment Instructions

Page 2
Figure 2

HASF2120_11EM1.qxd:HASF212009EM1.qxd 7/14/11 2:20 PM Page 2

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

F E AT U R E S - O P E R AT I O N S

F E AT U R E S - O P E R AT I O N S

When using electrical appliances, basic safety precautions should always be taken including the following:

1.Read all instructions before using this appliance.

2.Use fan only for purposes described in the instruction manual.

3.To protect against electrical shock do not immerse unit, plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet.

4.Close supervision is necessary when any appliance is used by or near children.

5.Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.

6.Avoid contact with moving parts.

7.Do not operate in the presence of explosive and/or flammable fumes.

8.To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance.

9.Do not operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or return to an authorized service facility for examination and/or repair.

10.Do not run cord under carpeting. Do not cover cord with throw rugs, runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

11.The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.

12.Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.

13.Do not use outdoors.

14.To disconnect, grip plug and pull from wall outlet. Never yank on cord.

15.Always use on a dry, level surface.

16.Do not operate fan until fully assembled with all parts properly in place.

17.This product is intended for household use ONLY and not for commercial or industrial applications.

18.WARNING: To reduce the risk of electrical shock and injury to persons, do not use in window.

19.WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

20.This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

Figure 1

ASSEMBLY INSTRUCTIONS

Base Assembly (See Figure 1)

You will need the base and four extension legs.

Push in the small tab located on the bottom of each extension leg and snap into base.

Pole Assembly (See Figure 2)

STEP 1: Remove the height adjustment collar from

the pole by turning counter clockwise.

STEP 2: Take the pole assembly,

with the solid end down, and insert it into

the base. The hollow end of the pole will be facing up.

STEP 3: Replace the height adjustment collar over the pole assembly, slide

it down the pole, and

secure by turning clockwise ( Refer to Figure 2 ).

Figure 3

 

 

G

H

I

 

 

 

 

 

 

J

 

 

 

 

 

 

K

 

 

 

 

 

 

L

 

 

 

 

 

 

Q

 

 

 

 

 

 

M

 

 

 

E

F

 

N

A

B

C

D

 

 

O

 

 

 

A.

Logo Plate

 

 

 

 

B.

Front Grill

 

 

 

P

 

C.

Fan Blade Cap

 

 

 

Fan Head Assembly (See Figure 4 - 6)

STEP 1: Position the rear grill over the motor shaft, making certain the 2 notches at the top and bottom of the rear grill fit over the 2 prongs on the motor housing. Please make sure the rear grill fits securely against the motor housing ( Refer to Figure 4 ).

STEP 2: Secure the rear grill in its place using the rear grill mounting-ring. Turn this ring clockwise and tighten firmly ( Refer to Figure 5 ).

STEP 3: Slide the fan blade; with the hollowed interior of the blade facing towards the rear grill firmly onto the motor shaft. Make sure the shaft protrudes from the front of the blade ( Refer to Figure 6 ).

STEP 4: Secure the fan blade onto the motor shaft by turning the fan blade cap in a counter-clockwise direction until it is firmly in place ( Refer to Figure 6 ).

STEP 5: Prepare the front grill by simply snapping the logo plate in place.

STEP 6: Center the front grill by aligning the Holmes® logo so it is horizontal and parallel to the floor. Then secure the front and rear grills completely together by snapping into place. Lastly, tighten the securing screw at the bottom of the rear grill.

Figure 4

Figure 5

Final Assembly

First, place fan head assembly onto the upper pole, lining up the fan post screw with the hole in the extension pole. Slide head assembly our upper pole and secure by tightening fan post screw. Lastly, insert the tilt adjustment knob into the neck joint and tighten in place.

NOTE: If your fan does not have a screw hole in the extension pole but instead has an indentation around the top of the pole; please do the following:

STEP 1: First, place the fan head assembly onto the upper pole and tighten the fan post screw until a secure fit is obtained.

STEP 2: Insert the tilt adjustment knob into the neck joint and tighten in place.

OPERATING INSTRUCTIONS

1.Set fan base on a dry, level surface.

2.Please make sure the Speed Control Knob is in the off position. The Speed Control Knob is located on the top of the Fan Motor Housing.

3.Plug cord into any standard 120 volt AC outlet.

4.The SPEED is adjusted by turning the control knob to the desired setting, OFF-HI-MED-LOspeed.

5.The OSCILLATION Knob is located on the top of the Fan Motor Housing. To Start Oscillation, push Oscillation Knob down. To Stop Oscillation, pull Oscillation Knob up.

ADJUSTMENT INSTRUCTIONS

Tilt Adjustment

Follow these instructions to tilt the Fan Head for upward angle air movement.

STEP 1: To change the tilting angle of the fan head; simply loosen the Tilt Adjustment Knob (see Figure 3).

STEP 2: Adjust the extension pole to the desired height, and firmly tighten the height adjustment collar in a clockwise direction.

CLEANING/MAINTENANCE

INSTRUCTIONS

Follow these instructions to correctly and safely care for your stand fan. Please remember:

REPLACEABLE FUSE

If your (5 Amp, 125 Volt) replaceable fuse blows, please order a new fuse at 1-800-546-5637. Follow the below instructions to replace the fuse on the plug.

User Servicing Instructions

1.Unplug your fan. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.

2.Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover down towards the prongs.

Note: Ensure that fuse cover is completely open before attempting to

remove fuse.

Figure 7

3. Remove fuse carefully by

Fuse

using a small screwdriver

Fuse cover

to pry the fuse out of the

 

compartment by the metal

 

ends of the fuse (see

Metal ends

Figure 7).

 

4.

Place plug on a solid, flat surface. Insert new 5

 

Amp, 125 Volt fuse into fuse compartment and use

 

a small screwdriver to secure the metal ends of the

 

fuse into the compartment.

 

Caution: Risk of fire. Replace fuse only with 5

5.

Amp, 125 Volt fuse.

Slide fuse cover closed completely. If fuse cover is

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

D.

Fan Blade

K.

Neck

E.

Rear-Grill Mounting

L.

Tilt-Adjustment Knob

F.

Ring

M.

Upper Pole

Rear Grill

N.

Height Adjustment

G.

Motor Shaft

O.

Collar

H.

Speed Control Knob

Lower Pole

I.

Oscillation Knob

P.

Extension Legs

J.

Motor Housing

Q.

Fan Post Screw

Figure 6

STEP 2: Move the fan head to the desired angle, and firmly tighten the knob to lock in place.

Height Adjustment

Follow these instructions to adjust the height of the fan.

STEP 1: Turn the height adjustment collar counter- clockwise to loosen pole.

difficult to close, make sure fuse is secured in place

completely by pressing down on metal ends of the

fuse.

6. Risk of fire. Do not replace attachment plug.

Contains a safety device (fuse) that should not be

removed. Discard product if the attachment plug is

damaged.

Page 1 Page 2
Image 2
Page 1 Page 2
Contents How to Obtain Warranty Service Fan Blade CleaningFan Head, Base, and Pole Cleaning FAN StorageCLEANING/MAINTENANCE Instructions Assembly InstructionsAdjustment Instructions Operating Instructions

HASF2120 specifications

The Holmes HASF2120 is an advanced air purifier designed to enhance indoor air quality while providing users with modern features and technologies. With the increasing awareness of air pollution and its effects on health, the HASF2120 serves as an essential tool for maintaining a clean and safe living environment.

One of the standout features of the Holmes HASF2120 is its powerful filtration system, which incorporates a true HEPA filter. This technology is capable of capturing up to 99.97% of airborne particles as small as 0.3 microns in size, including allergens like dust, pollen, and pet dander. This makes it an excellent choice for allergy sufferers and those looking to reduce irritants in their homes. Additionally, the device includes an activated carbon pre-filter that helps to neutralize odors from pets, smoke, and cooking, ensuring that the air smells fresh and clean.

The HASF2120 is designed with multiple fan speed settings, which allow users to customize the airflow according to their preferences and room conditions. The quiet operation of the unit, even at higher settings, makes it suitable for bedrooms or living areas where noise levels need to be minimized. The intuitive control panel provides ease of use, enabling users to adjust settings with just a few simple presses.

In terms of design, the Holmes HASF2120 boasts a sleek and modern aesthetic that can seamlessly fit into any home decor. Its compact size ensures it doesn’t take up too much space, while still being effective for medium-sized rooms. The lightweight construction makes it easy to move from one room to another, providing flexibility for users.

Moreover, the HASF2120 is equipped with a filter replacement indicator, which alerts users when it’s time to change the filter. This feature helps maintain optimal performance of the air purifier, ensuring continuous air quality improvement without the guesswork.

The energy-efficient design of the Holmes HASF2120 is another key aspect worth mentioning. It operates using minimal electricity, making it an eco-friendly choice that doesn’t significantly impact energy bills.

In summary, the Holmes HASF2120 combines effective air purification with modern technology to create a user-friendly environment for families. Its excellent filtration, customizable settings, sleek design, and energy efficiency make it a standout choice for anyone looking to improve their indoor air quality.
Top Page Image Contents