Holmes HASF1406 warranty Adjustment Instructions, Assembly Instructions, Operating Instructions

HASF1406_07EM1.qxd 9/29/07 10:38 Page 2

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

F E AT U R E S - O P E R AT I O N S

F E AT U R E S - O P E R AT I O N S C L E A N I N G / M A I N T E N A N C E

When using electrical appliances, basic safety precautions should always be taken including the following:

1.	Read all instructions before using this appliance.
2.	Use fan only for purposes described in the instruction
	manual.
3.	To protect against electrical shock do not immerse unit,
	plug or cord in water or spray with liquids and plug
	the appliance directly into a 120V AC electrical outlet.
4.	Close supervision is necessary when any appliance is
	used by or near children.
5.	Unplug from outlet when not in use, when moving

17.WARNING: To reduce the risk of electrical shock and injury to persons, do not use in window.

18.WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state speed control device.

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

Figure 1		Q	P	O	N	M
S	R						L
T
							K
							J
					H		I
				G			F

Figure 3 D

E

C

B

A

6.Secure the Front Grill (T) to the Rear Grill of the fan by positioning the hanging clip of the Front Grill over the Rear Grill. Close the remaining four Grill Clips (N) of the Front Grill over the Rear Grill. Refer to Figure 8.

ADJUSTMENT INSTRUCTIONS

Fan Head Tilt Adjustment

Loosen Tilt-Adjustment Knob (I), move fan head to desired angle, and tighten Tilt Adjustment Knob to lock in place.

CLEANING/MAINTENANCE INSTRUCTIONS

Follow these instructions to correctly and safely care for your fan.

• Always unplug the fan before cleaning or disassembling.

• Be sure to clean your fan with a soft cloth moistened

with a mild soap solution.

• Do not allow water to drip on or enter into the fan

motor housing.

• Do not use gasoline, thinner, or benzene as a cleaner.

• Lightly run a vacuum cleaner nozzle over the fan grill

to remove any dust or dirt that may have accumulated.

	fan from one location to another, before putting on
	or taking off parts and before cleaning.
6.	Avoid contact with moving parts.
7.	Do not operate in the presence of explosive and/or
	flammable fumes.
8.	To avoid fire hazard, NEVER place the cord under
	rugs or any parts near an open flame, cooking or
	other heating appliance.
9.	Do not operate any appliance with a damaged cord
	or plug after the appliance malfunctions, or has been
	dropped/damaged in any manner.
10.	The use of attachments not recommended or sold by
	the appliance manufacturer may cause hazards.
11.	Do not let the cord hang over the edge of a table,
	counter or come in contact with hot surfaces or leave
	exposed to high traffic areas.
12.	Do not use outdoors.
13.	To disconnect, grip plug and pull from wall outlet.
	Never yank on cord.

ASSEMBLY INSTRUCTIONS

Tools required: One Phillips head screw driver

Assembly time: 10-15 minutes

1.	Secure the Base Weight (C), Base (D), and Long
	Extension Pole (E) together using the L-shaped screw
	(A) and Washer (B). Refer to Figure 3 for the correct
	alignment of the Long Extension Pole to the Base.
2.	Align the holes of the Long Extension Pole (E) and
	Short Extension Pole (G) together and secure with
	Phillips head screw (F) and tighten with screw driver.
	Refer to Figure 4.
3.	Align the holes of the neck of the Short Extension Pole and
	the Neck (H) together and secure with the Phillips head
	screw (F) and tighten with screw driver. Refer to Figure 5.
4.	Secure the Rear Grill (O) to the Motor Housing (K) by
	tightening the Rear Grill Nut (P). Refer to Figure 6

A.(1) L-shaped screw

B.(1) Washer

C.Weight

D.Base

E.Long Extension Pole

F.(2) Phillips head screws

G.Short Extension Pole

H.Neck

I.Tilt Adjustment Knob

J.Fan Speed Pull Chain

K.Motor Housing

L.Oscillation Knob

M.Motor Shaft

N.Grill Clips

O.Rear Grill

P.Rear Grill Nut

Q.(1) Blade screw

E

D

C

B A

R.Blade

S.Hanging Clip

T.Front Grill

Figure 4 G

F E

Figure 5

H

OPERATING INSTRUCTIONS

Fan Speed Pull Chain (J)

1st = High ( III ) 2nd = Medium ( II ) 3rd = Low ( I )

4th = Off (o)

Oscillation Knob (L) ( ) Push, Pull = Oscillation On, Off

Figure 7

FAN BLADE CLEANING

Make sure the fan is unplugged before disassembling and cleaning the fan blade. Unclip and remove the front grill. Wipe the blade with a soft cloth moistened with a mild soap solution. DO NOT allow any liquid to drip into or enter the Motor Housing. Re-clip the front grill onto the fan. Make sure all parts are secured prior to operating the fan.

FAN STORAGE INSTRUCTIONS

Your fan should be stored in the off-season in its original box. It is important to keep it in a safe, dry location.

•We recommend using the original (or appropriately sized) box.

•Please remember to protect the fan from dust or moisture.

14.	Always use on a dry, level surface.
15.	Do not operate fan until fully assembled with all
	parts properly in place.
16.	This product is intended for household use ONLY and
	not for commercial or industrial applications.

for correct positioning of the Rear Grill to the Motor

Housing.

5. Secure the Fan Blade (R) to the Motor Shaft (M) by

tightening the Blade Screw (Q) with a screw driver.

Refer to Figure 7 for the correct alignment of the Fan

Blade to the Blade Shaft.

Figure 2

A (X 1)

Q (X 1), F (X 2)

F

G

Figure 6

3 pt

Figure 8

S

If you have any questions regarding your product or would like to learn more about other Holmes® products, please contact our Consumer Service Department at 1-800-546- 5637 or visit our website at www.holmesproducts.com

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

B (X 1)

O P