Holmes HAWF3095 warranty Installation Instructions, Operating Instructions

Page 2
Metal ends

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

F E AT U R E S - O P E R AT I O N S

F E AT U R E S - O P E R AT I O N S C L E A N I N G / M A I N T E N A N C E

When using electrical appliances, basic safety precautions should always be taken including the following:

1.

Read all instructions before using this appliance.

2.

Use fan only for purposes described in the instruction

 

manual.

3.

To protect against electrical shock do not immerse unit,

 

plug or cord in water or spray with liquids and plug the

 

appliance directly into a 120V AC electrical outlet.

4.

Close supervision is necessary when any appliance is

 

used by or near children.

5.

Unplug from outlet when not in use, when moving

 

fan from one location to another, before putting on

 

or taking off parts and before cleaning.

6.

Avoid contact with moving parts.

7.

Do not operate in the presence of explosive and/or

 

flammable fumes.

8.

To avoid fire hazard, NEVER place the cord under

 

rugs or any parts near an open flame, cooking or

 

other heating appliance.

9.

Do not operate any appliance with a damaged cord

 

or plug after the appliance malfunctions, or has been

 

dropped/damaged in any manner. Discard fan or

 

return to an authorized service facility for

 

examination and/or repair.

10.

Do not run cord under carpeting. Do not cover cord

 

with throw rugs, runner, or similar coverings. Do not

 

route cord under furniture or appliances. Arrange

 

cord away from traffic area and where it will not be

 

tripped over.

13.Do not use outdoors.

14.To disconnect, grip plug and pull from wall outlet. Never yank on cord.

15.Always use on a dry, level surface.

16.Do not operate fan until fully assembled with all parts properly in place.

17.This product is intended for household use ONLY and not for commercial or industrial applications.

18.WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

19.This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.

The window fan comes fully assembled and is ready for immediate installation.

This window fan has been designed to fit double-hung windows with minimum openings of 24 inches (60 cm) wide and 12 inches (30 cm) high.

NOTE: THIS FAN IS DESIGNED AND RECOMMENDED FOR USE WITH A SCREEN IN THE WINDOW.

Window Fan Installation

1.Align the Window Fan horizontally in the window with the controls facing you and the Built-In Extender Panel (J) to the right.

2.Set the fan into your window opening.

3.If the fan does not fit snugly to the left and right of the window casing, pull out the Built-In Extender Panel (J) until the fan sits safely in your window.

4.If the fan still does not fit snugly attach the Slider Safe® Extender Panel located in the polyfoam packaging in the original box. Align the slot in the Slider Safe® Extender Panel along the tab located on the left side of your Window Fan. Slide the Slider Safe® Extender Panel completely down the tab until it is flush on both the top and bottom of the Window Fan.

5.To keep the fan in place, carefully close the window so that the bottom edge of the window rests on the flat area on the top of the fan.

For Slider Windows

1.Set the Fan Vertically in your window opening with the left side of the fan situated on the bottom and the Built-In-Extender panel on top.

2.Set the fan into your window opening (note that in most cases the window screen does not have to be removed or left open).

3.If the fan does not fit snugly to the top and bottom of the window casing, attach the Slider Safe® Extender Panel and adjust the built-in extender screen until the fan fits securely in your window.

WARNING: BE SURE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON THE FAN WHILE IT IS IN THE WINDOW.

OPERATING INSTRUCTIONS

1.Plug cord into any standard 120 volt AC outlet.

2.To turn the fan on and control the speed, press the Mode Button (D). Note that pressing the mode button will allow you to cycle through the speed setting (High = 3, Med = 2, Low = 1) as well as the Automatic Thermostat Temperature settings (Auto High = A3, Auto Medium = A2, Auto Low = A1). 0 indicates the Off position.

3.Set the airflow direction by sliding the fan directional switches located above each fan blade. Note that the fan blades work independently from one another and can be used for air intake (bring fresh air in from outside), exhaust (push air out from within the room) or exchange (cycles air in and out of the room simultaneously).

Auto Mode

Your fan is equipped with the AccuTemp Plus™ Digital Thermostat that will automatically turn the fan ON and OFF depending upon the preset comfort temperature. This is ideal for nighttime operation when temperatures can drop below comfort levels.

Setting Auto Mode

1.Press the Mode button (D) to scroll to the desired auto speed setting (A3, A2, or A1).

2.Choose the desired temperature setting by pressing the Temp Up (+) or Temp Down (-) buttons. You may select a temperature between 60 and 80 degrees Fahrenheit. Once the desired temperature is set, the digital display will return to show the ambient room temperature. View the set temperature by pressing either the Temp Up (+) or Temp Down (-) buttons. For example, if you set your thermostat to 75 degrees then your fan will run until the set temperature is reached. Once the temperature rises above the set temperature the fan will automatically turn on again.

•If Timer is set when fan is ON, the time displayed will turn the fan OFF once elapsed. If Timer is set when fan is OFF, the time displayed will turn the fan ON. (The default ON speed setting is Manual Low)

•Timer function can be turned off by pressing the MODE key at any time.

CLEANING/MAINTENANCE

INSTRUCTIONS

Follow these instructions to correctly and safely care for your fan. Please remember:

REPLACEABLE FUSE

If your (5 Amp, 125 Volt) replaceable fuse blows, please order a new fuse at 1-800-546-5637. Follow the below instructions to replace the fuse on the plug.

User Servicing Instructions

1.Unplug your fan. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.

2.Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover down towards the prongs.

NOTE: Ensure that fuse

cover is completely open

Figure 2

before attempting to

Fuse

remove fuse.

Fuse cover

3. Remove fuse carefully by

11.

The use of attachments not recommended or sold by

 

the appliance manufacturer may cause hazards.

12.

Do not let the cord hang over the edge of a table,

 

counter or come in contact with hot surfaces or leave

 

exposed to high traffic areas.

Figure 1

B

C

D

E

F

G

H

 

 

 

I

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A.

Front Grill

 

 

 

 

 

 

 

 

B.

Left Fan Directional Switch

 

 

 

 

 

 

 

 

C.

Control Panel

 

 

 

 

 

 

 

 

IMPORTANT: If the fan does not start in the Auto mode, please be sure that the set temperature is below the current room temperature. Lower the set temperature if you would like for the fan to start or switch over to the manual speed modes.

Setting the Timer

using a small screwdriver

to pry the fuse out of the

compartment by the metal ends of the fuse. (see Figure 2)

4. Place plug on a solid, flat surface. Insert new 5 Amp,

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

D.

Mode Button

J

E.

LED Display

F.Temp Up (+)

G.Temp Down (-)

H.

Right Fan Directional Switch

A

I.

Extender Locks

I

J.

Built-In Extender Panel

1.Hold both the Temp Up (+) and Temp Down (-) buttons down until the digital display flashes “00”.

2.Press the (+) or (-) buttons to change time in 1 hour increments. Note selection ranges from 1 to 16 hours. When in the timer mode, the time remaining will be displayed.

NOTE:

•The Timer Light will glow indicating the timer function is active.

125 Volt fuse into fuse compartment and use a small

screwdriver to secure the metal ends of the fuse into

the compartment.

CAUTION: Risk of fire. Replace fuse only with 5

Amp, 125 Volt fuse.

5. Slide fuse cover closed completely. If fuse cover is

difficult to close, make sure fuse is secured in place

completely by pressing down on metal ends of the fuse.

HAWF3095_11EM1.indd 2

7/15/11 9:59 AM

Page 1 Page 2
Image 2
Page 1 Page 2
Contents Window FAN Accessories FAN StorageOperating Instructions Installation InstructionsCLEANING/MAINTENANCE Instructions

HAWF3095 specifications

The Holmes HAWF3095 is a powerful and efficient fan that stands out in the market for its innovative design and impressive performance features. This fan is ideal for those seeking an effective solution to combat heat and circulate air, making it the perfect addition to any home or office environment.

One of the main features of the Holmes HAWF3095 is its dual blade system, which provides enhanced air circulation. This unique design allows the fan to push a greater volume of air, creating a refreshing breeze that can be felt throughout the room. With adjustable speed settings, users have the flexibility to customize airflow according to their preferences, whether it’s a gentle breeze for a comfortable reading session or a powerful gust for those hot summer days.

The HAWF3095 is also equipped with a 90-degree pivoting head. This functionality allows users to direct airflow more precisely, ensuring that the cooling effect reaches the desired area. Whether placed in a corner or on a tabletop, the fan’s pivoting head makes it easy to optimize airflow across larger spaces.

One of the standout technologies in the Holmes HAWF3095 is its Whisper Quiet operation. Unlike many standard fans, this model is designed to operate quietly, making it ideal for use in bedrooms, offices, or any space where noise levels need to be minimized. This feature allows users to enjoy a cool breeze without the disruptive sound that can often accompany powerful fans.

The stylish and compact design of the HAWF3095 ensures that it can fit seamlessly into any décor. Available in neutral colors, it is both functional and aesthetically pleasing, which is a significant advantage for consumers looking for equipment that enhances their interior style.

Additionally, the Holmes HAWF3095 is lightweight and portable, making it easy to move from one room to another. It is energy-efficient, which helps users save money on their electricity bills while maintaining a comfortable atmosphere in their homes.

In summary, the Holmes HAWF3095 provides an excellent balance of power, versatility, and aesthetic appeal. With its dual blade system, adjustable speeds, pivoting head, Whisper Quiet technology, and portable design, this fan is a top choice for those seeking effective air circulation in their living or working spaces.
Top Page Image Contents