Mr. Heater Portable Buddy

LIGHTING / OPERATING INSTRUCTIONS FOR USE WITH DISPOSABLE 1 LB. PROPANE CYLINDERS:

WARNING: Always inspect propane cylinder and heater propane connections for damage, dirt, and debris before attaching propane cylinder. Do not use if head of cylinder is damaged, punctured or deteriorated.

ALWAYS ATTACH OR DETACH CYLINDER OUTDOORS AWAY FROM FLAMES, OTHER IGNITION SOURCES, AND ONLY WHEN HEATER IS COOL TO TOUCH. NEVER SMOKE WHEN ATTACHING OR REMOVING PROPANE CYLINDER OR MAKING REMOTE CONNECTIONS!

•Use only LP-gas cylinders marked in accordance with the U.S. Dept. of Transportation (DOT).

•Use only 16.4 oz. (1 lb.) disposable cylinders that mate with No. 600 valve connection.

•Heater and attached cylinder must be in an upright position during operation.

•Make sure four-position Control Knob is in “OFF” position; see Figure 1.

Figure1

•Screw 1 lb. disposable LP-gas supply cylinder clockwise (from bottom) into portable heater until hand-tight.

•Check cylinder connection for leaks with soapy water at the threaded connection under the domed plastic cover where the cylinder screws into the regulator. SEE WARNING! ON PLASTIC COVER.

•Depress and turn Control Knob counterclockwise to “PILOT” position and hold for 30-60 seconds.

•Depress red spark ignition button to light pilot flame (repeat until pilot lights) and continue to hold Control Knob down and at “PILOT” position for 30-60 seconds to enable Pilot Light Safety System.

•Fully turn Control Knob to “HI” position to light burner tile. Leave on “HI” position until burner tile turns bright orange.

•After burner tile has turned bright orange, adjust heat output by turning Control Knob to desired position

(“LO” or “HI” setting)

•DO NOT OPERATE HEATER UNLESS CONTROL KNOB IS SECURED IN A POSITION MARKED “HI”, “LO” or “PILOT”.

•To shut off heater, slightly push down and turn Control Knob clockwise to “OFF” position.

•CAUTION: After turning heater off, wire guard will remain hot. Allow to thoroughly cool before storing.

•Do not operate, store or remove cylinder near flam- mable items or ignition sources.

•LP-GAS CYLINDERS MUST BE DISCONNECTED FROM HEATER WHEN NOT IN USE!

LIGHTING / OPERATING INSTRUCTIONS FOR USE WITH HOSE CONNECTED TO A REMOTE CYLINDER, MAXIMUM SIZE 20 LBS:

•This Heater may be used in a Recreational Enclosure or Temporary Construction Work Enclosure with a Remote Refillable Propane Cylinder ONLY when the Cylinder is Located Outdoors and the Heater is Used with Mr. Heater Hose No. F273701or F273702.

•DANGER: NEVER bring a refillable propane cylinder indoors. A fire or explosion can occur causing property damage, serious injury or death!

•Inspect the hose before each use of the heater. If there is excessive abrasion or wear, or the hose is cut, replace prior to using the heater with one of the Mr. Heater Hose No’s. shown above.

•The propane cylinder must include a listed overfilling protection device as well as a collar to protect the cylinder valve.

•Heater must be in an upright position during operation.

•Make sure four-position Control Knob is in “OFF” position; see Figure 1, at left.

•Screw hose connector into regulator on heater and screw connector on other end of hose into LP-gas supply cylinder valve. Tighten all hose connections.

•Check all hose connections for leaks with soapy water at the threaded connection under the domed plastic cover where the hose connector screws into the regulator and at LP-gas supply cylinder. SEE WARNING! ON PLASTIC COVER.

•Open valve at LP-gas supply cylinder.

•Depress and turn Control Knob counterclockwise to “PILOT” position and hold for 1 - 2 minutes. This may take longer to purge air from the supply hose depend- ing on the length of the hose being used.

Operating Instructions and Owner’s Manual

MH9B specifications

The Enerco MH9B is a versatile and portable propane-powered heater designed to deliver efficient warmth in various settings such as garages, construction sites, and outdoor events. Renowned for its robust design and reliable performance, the MH9B has become a top choice for users looking for a reliable heating solution.

One of the standout features of the MH9B is its exceptional heat output. With an impressive heating capacity of up to 9,000 BTUs, this heater can effectively warm spaces up to 225 square feet. This makes it suitable for both indoor and outdoor use, providing comfort in chilly conditions.

The MH9B is equipped with advanced safety features to ensure user protection and peace of mind. It includes an automatic shut-off functionality that activates if the heater is tipped over, as well as a built-in oxygen depletion sensor that will shut the unit off if oxygen levels drop too low. These safety measures are crucial, especially when using the heater in enclosed spaces.

In terms of design, the Enerco MH9B boasts a compact and lightweight structure. Weighing only about 9 lbs, it is highly portable, allowing users to transport it easily from one location to another. The integrated handle further enhances its portability, making it simple to carry and move as needed.

The operation of the MH9B is straightforward. It utilizes a standard 1-pound propane bottle, which is readily available and easy to replace. Users can expect a burn time of approximately 3 hours on the highest setting, making it a practical choice for both short-term and extended heating needs.

Additionally, the heater incorporates a durable, rugged construction designed to withstand the rigors of work and outdoor environments. The powerful flame and adjustable heat settings allow users to customize their heating experience, whether for warming a workshop or providing comfort during outdoor gatherings.

Overall, the Enerco MH9B is an effective and user-friendly propane heater. Its combination of high heat output, portability, and safety features makes it an ideal choice for anyone in need of reliable heating, whether indoors or outside. Whether for professional use on job sites or for personal enjoyment during outings, the MH9B continues to be a trusted solution for warmth in diverse conditions.