Enerco 2000ID 3000ID, 4000ID, 1000ID owner manual Troubleshooting

Page 6

Troubleshooting

TROUBLE

Cause

SOLUTION

Motor does not start, no ignition

No electrical current

Check mains (should be 120 V – 1~ – 60 Hz)

 

 

Check proper positioning and functioning of switch

 

 

Check fuse

 

Wrong setting of room ther-

Check correct setting of heater control. If thermostat, make

 

mostat or other control

sure selected temperature is higher than room temperature

 

Thermostat or other control

Replace control device

 

defective

 

 

Electrical motor defective

Replace electrical motor

 

Electrical motor bearings

Replace electrical motor bearings

 

defective

 

 

Burned out condenser

Replace condenser

 

 

 

Motor starts, no ignition or cuts out

Electric ignitor defective

Check connection of H.V. Ieads to electrodes and transformer

 

 

Check electrodes setting (see scheme “GAP OF ELECTRODES”)

 

 

Check electrodes for cleanliness

 

 

Replace H.V. transformer

 

Flame control box defective

Replace control box

 

Photocell defective

Clean or replace photocell

 

Not enough or no fuel at all

Check state of motor-pump plastic coupling

 

at burner

Check fuel line system including fuel filter for possible leaks

 

 

 

 

Clean or replace oil nozzle

 

Solenoid defective

Check electrical connection

 

 

Check thermostat LI

 

 

Clean or replace solenoid

 

 

 

Motor starts, heater emits smoke

Not enough combustion air

Make sure air inlet and outlet are free

 

 

Check setting of combustion air flap

 

 

Clean burner disc

 

Too much combustion air

Check setting of combustion air flap

 

Fuel contaminated or con-

Drain fuel in tank with clean fuel

 

tains water

Clean oil filter

 

 

 

Air leaks in fuel circuit

Check the seals on the ducts and the diesel filter

 

Not enough fuel at burner

Check pump pressure

 

 

Clean or replace fuel nozzle

 

Too much fuel at burner

Check pump pressure

 

 

Replace nozzle

 

 

 

Heater does not stop

Solenoid

Replace solenoid coil or complete solenoid

 

 

 

If heater still not working properly, please revert to nearest authorized dealer.

ENERCO GROUP, INC. Indirect Fired Portable Heater

6

Operating Instructions and Owner’s Manual

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Indirect Fired Portable Heater General Hazard Warning General Recommendations Stopping the Heater Safety DevicesOperation TransportVentilation MaintenanceFlue Connections Diagram GAP of ElectrodesTroubleshooting Wiring Diagram 1000ID Series Models Drawing Legend Fuse Control Transformer H.V Room ThermostatOverheat Thermostat Relays LI1 Wiring Diagram 2000ID and 3000ID Series ModelsDrawing Legend EV1Wiring Diagram 4000ID Series Models LI253 54 1000ID Series Indirect-Fired Portable Heater Parts List Stock No Description62 63 Stock No 2000 3000 Description 4000ID Series Indirect-Fired Portable Heaters Manual Stock No Description Column intentionally Left blank 1000ID 2000ID Safe place for future reference. Do not allow ’œuvre Produit le acheté avez vous qui de détaillant du0001-251-800 au HEATER/HEATSTAR .MR Locaux DétaillantsMM 1/4 FE Nipplo MM 1/8 FE NipploM5 Ecrou M20408 EtrierCarter JointTiré-Indirect Portatif Chauffage Série 4000ID Tiré-Indirect Portatif Chauffage Série 4000ID Tiré-Indirect Portatif Chauffage Série 2000ID/3000ID 2000ID/3000ID Série Chauffage Tiré-Indirect Portatif Chauffage Série 1000ID Portatif Indirect-tiré 1000ID Série ChauffageSecurite de Coffret Electrovanne Models Series 4000 Diagram WiringTerre ’alimentation temoin Lampe Relais Surchauffe de ThermostatModels Series 3000 and 2000 Diagram Wiring Models Series 1000 Diagram Wiring Solutions ET Causes Fonctionnement DE Anomalies Installeur votre Ou revendeur votre par conformité en installation votreArret EX Combustible DE Source DE PAS N’UTILISEZ FonctionnementChauffage DE L’APPAREIL ’EXTÉRIEUR, À Réservoir LE Toujours Remplissez4000id hs 3000id hs 2000id hs 1000id hs 3000id mh 2000id mh 1000id mhSécurité de Artifices Parties de listeConnexions de schémas OpérationPortatif Chauffage Tiré Indirect

4000ID, 3000ID, 2000ID 3000ID, 1000ID specifications

Enerco has established itself as a leading name in the heating solutions market with its innovative range of infrared heaters, including the Enerco 4000ID, 3000ID, 2000ID, and 1000ID models. Each model is designed to cater to various heating needs, making them suitable for both residential and commercial applications.

The Enerco 4000ID stands out with its powerful 4000-watt output, making it ideal for larger spaces. Its advanced infrared technology heats objects directly rather than warming the air, ensuring a more energy-efficient operation. This model features a built-in temperature control system, allowing users to set and maintain their desired comfort level easily. Additionally, the 4000ID has a rugged design, suitable for outdoor use, with weatherproof casing that enhances durability.

For medium-sized areas, the Enerco 3000ID is an excellent choice. With a 3000-watt output, it combines efficiency with performance. Like its larger counterpart, the 3000ID utilizes infrared heating technology, providing comfort and warmth without the inefficiencies of conventional heating systems. It also comes equipped with safety features such as an automatic shut-off mechanism and overheat protection, ensuring peace of mind during operation.

The Enerco 2000ID is a versatile option for various applications, including workshops, garages, and smaller commercial spaces. With a output of 2000 watts, it effectively delivers warmth to targeted areas. It features adjustable heat settings, allowing users to customize their heating experience based on specific requirements. Its portable design enables easy relocation, ensuring that warmth is just a reach away.

The Enerco 1000ID is the most compact model in the lineup, committed to providing energy-efficient heating in tight spaces. With a maximum output of 1000 watts, it is perfect for small rooms or as supplementary heating in larger areas. Its lightweight design and ease of installation make it an attractive option for users seeking a straightforward heating solution without compromising on effectiveness.

All models in the Enerco infrared heater range share key characteristics, including fast heat-up times, silent operation, and minimal maintenance. The infrared heating technology employed enhances energy efficiency, resulting in lower operational costs over time. These heaters not only heat spaces quickly but also create a comfortable environment without the dryness associated with traditional heating systems.

In summary, Enerco's infrared heater models—4000ID, 3000ID, 2000ID, and 1000ID—offer diverse solutions for heating needs, with each model tailored to specific environments. With their emphasis on efficiency, durability, and user-friendly features, Enerco heaters represent a smart investment for anyone looking to enhance their heating experience.
Top Page Image Contents