Lennox International Inc G20 Lighting Information and Operation, Gas Valve Operation Figures 3

Page 4

product. Lennox strongly recommends annual in- spection and maintenance of this appliance. Contact

your independent Lennox dealer for an inspection by a qualified service technician.

LIGHTING INFORMATION AND OPERATION

WARNING

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or death.

BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. Use only your hand to push in or turn the gas control knob or lever. Never use tools. If the knob or lever will not push in or turn by hand, do not try to repair it, call a qualified ser- vice technician. Force or attempted repair may result in a fire or explosion.

To place G20E or G20X furnace into operation:

G20E or G20X units are equipped with an intermittent pi- lot ignition system. Do not attempt to manually light pilots on these furnaces. Each time thermostat calls for heat, the pilot will automatically light. The pilot does not burn when there is no call for heat on units with electronic igni- tions.

Gas Valve Operation (Figures 3 and 4)

1- STOP! Read the safety information at the beginning of this section.

2- Set thermostat to lowest setting. See figure 2.

+21(<:(//95￿￿￿￿6(5,(6*$69$/9(

ON

OFF

GAS VALVE SHOWN IN OFF POSITION

52%76+(5FIGURE$:￿￿￿￿3*$69$/9(

GAS VALVE

 

SELECTOR

 

ARM

 

IN OFF

 

POSITION

),*85(￿

7- Wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. If you do not smell gas go to next step.

8- Honeywell VR8204 Gas Valves - Turn the knob on

the gas valve counterclockwise to ON. Robertshaw 7200 Gas Valve - Depress the lever and move to ON position. Do not force.

THERMOSTATS

9-

Replace control access panel.

10-

Turn on all electrical power to unit.

 

 

11-

Set thermostat to desired setting.

 

 

NOTE-When unit is initially started, steps 1 through 11

 

 

may need to be repeated to purge air from pilot line.

 

12-

If the furnace still will not operate, follow the instruc-

 

 

tions “To Turn Off Gas To Unit” and call your service

 

 

technician or gas supplier.

FIGURE 2

To Turn Off Gas To Unit

3- Turn off all electrical power to appliance.

4- This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.3DJH￿

5- Remove control access panel.

6- Honeywell VR8204 Gas Valve - Turn the knob on the

gas valve clockwise to OFF. See figure 3. Robertshaw 7200 Gas Valve - Depress the lever and move to OFF position. Do not force. See figure 4.

1- Set thermostat to lowest setting.

2- Turn off all electrical power to unit if service is to be performed.

3- Remove control access panel.

4- Honeywell VR8204 Gas Valves - Turn the knob on the

gas valve clockwise to OFF.

Robertshaw 7200 Gas Valve - Depress the lever and move to OFF position. Do not force.

5- Replace control access panel.

Image 4
Contents 65,6 21752/%2 Important Directions Lighting Information and Operation To place G20E or G20X furnace into operationGas Valve Operation Figures 3 To Turn Off Gas To UnitVenting System Inspection Blocked Vent SHUT-OFF SystemFilters BlowerService Reminder

G20 specifications

Lennox International Inc G20 is a cutting-edge HVAC (heating, ventilation, and air conditioning) system that embodies innovation and efficiency. Known for its commitment to sustainability and advanced technology, the G20 model stands out in the competitive landscape of climate control solutions.

One of the defining features of the Lennox G20 is its high efficiency rating. The unit is designed to operate with superior energy efficiency, helping homeowners and businesses significantly reduce their energy consumption and utility bills. With an impressive SEER (Seasonal Energy Efficiency Ratio) rating, the G20 harnesses state-of-the-art technology to provide optimal cooling performance while minimizing environmental impact.

The G20 incorporates advanced smart technologies that enhance user experience. Lennox's proprietary iComfort S30 smart thermostat is compatible with this model, allowing users to monitor and control their indoor climate remotely via a smartphone app. This integration not only improves convenience but also helps optimize energy usage by allowing settings to be adjusted according to occupancy patterns.

Innovative technology extends to the system’s variable-speed compressor. This feature enables the G20 to adjust its cooling output based on the specific needs of the environment, ensuring consistent comfort without fluctuations. The result is a quieter operation and improved indoor air quality as the system runs for longer periods at lower speeds, effectively removing humidity.

Durability is another hallmark of the Lennox G20. Built with high-quality materials, the unit is designed to withstand a range of weather conditions and require minimal maintenance. Its robust construction ensures reliability, contributing to a long operational lifespan, which is a significant consideration for both residential and commercial applications.

The G20 also prioritizes eco-friendliness, utilizing R-410A refrigerant, which has a lower environmental impact compared to older refrigerants. Furthermore, the system is engineered with sound-dampening technology that reduces operational noise, creating a more pleasant indoor environment.

In summary, Lennox International Inc G20 represents state-of-the-art HVAC technology. Its energy efficiency, smart features, variable-speed compressor, durability, and eco-friendliness make it a premium choice for those seeking dependable climate control solutions. The G20 not only enhances comfort but also aligns with modern sustainability goals, making it a forward-thinking investment in a responsible future.