System Checks, Static Pressure Test | Atwood Mobile Products 2540

THERMOSTAT INSTALLATION (MODEL 2H2C)

FURNACE - MODEL 2540 MUST USE THIS THERMOSTAT

The thermostat is very sensitive. HANDLE WITH CARE AT ALL TIMES.

Locate thermostat 48˝ to 54˝ above floor on an INTERIOR wall. Pick a dry area where air circulation is good. EXTERIOR wall location must have a 3/4˝ spacer between thermostat and exterior wall.

1.Be sure all electrical power has been disconnected from the air con- ditioner, furnace and the power supply.

2.Do not install the thermostat where there are unusual heating condi- tions: such as direct sunlight, heat producing appliances (television, radio, wall lamp, etc.) or a furnace or air conditioner supply register.

3.ATTACHING THE WALL THERMOSTAT. Separate the thermostat body from the sub-base by gently squeezing the top and bottom. Pull wires through access hole in base plate. Attach thermostat sub-base to the wall at the desired mounting location. Mount the sub-base to the wall before connecting the wires. See instruction provided with thermostat.

SYSTEM CHECKS

NOTE: A SOFT lockout is a condition that is timed and will make addition- al attempts to correct the problem. A HARD lockout requires reset of the thermostat or turning the power switch off then back on.

PROPANE GAS PRESSURE TEST

The furnace and any individual shut-off valve must be disconnected from gas supply piping system during any pressure testing of system at test pressures of more than 1/2 PSI.

Before furnace is connected piping systems must be tested to be leak free. The test must maintain air pressure of at least 6˝ of mercury or 3 PSI for at least 10 minutes.

The entire piping system must be maintained within a range of 10-14˝ W.C. when all appliances are in operation. Test gas connections for leakage with a leak test solution.

STATIC PRESSURE TEST

CASING STATIC PRESSURE TABLE

If duct static pressure cannot be set, casing static pressure should not exceed the values listed below when taken cold.

WARNING

FIRE OR EXPLOSION

•Never check for leaks with an open flame.

DIAGNOSTIC CHART

A diagnostic LED is located inside the exterior access cover on the out- side edge of the horizontal (2) stage control board. The following graph defines the codes.

NUMBER OF LED FLASHES	DIANOSTIC INFORMATION	LOCKOUT
1	Low Input voltage	SOFT
2	Ignition Failure	SOFT
3	Open High Limit	SOFT
4	Stuck Sail Switch	HARD
5	Module Fault	HARD

DUCTING SYSTEM	OPERATING VOLTS	FLEXIBLE	HARD
DC MODELS	12	0.25˝ W.C.	0.35˝ W.C.

Voltage greater than indicated will cause higher static readings. Reducing the number of duct turns and stretching ducts will increase air flow and reduce static pressure. Adding ducts or increasing dis- charge system (hard ducting) will also reduce static pressure. NOTE: Special tool required to take casing static pressures.

Location for Static Pressure Tap for casing is on the back of casing (top left corner) (FIG 3).

2-STAGE - MODEL 2540

4 WIRING

ELECTRONIC

DIGITAL

THERMOSTAT

MOTOR

RED

BLACK

YELLOW

+12 VDC				RED
+THERMO		1	1
+THERMO		2	2	BLUE
		2	2	BLUE

-12 VDC		3	3	YELLOW
-12 VDC		4	4
-THERMO		4	4
				GREEN
		5	5	GREEN
		5	5
		6	6
	BULK HEAD
	CONNECTOR

CUSTOMER SUPPLIED WIRE

WHITE

LIMIT SWITCH

RED
	IGNITION	ELECTRODE
DUAL	CONTROL	CHASSIS
DUAL
CONTROL
CONTROL		GROUND
6 5 4 3 21		GROUND
6 5 4 3 21
WHITE		HIGH TENSION
WHITE
BLACK	ORANGE	RED
	BLUE	RED
	BLUE
	YELLOW

BROWN

SAIL

SWITCH

CHASSIS

GROUND

IMPORTANT: If any original wire has to	VALVE
be replaced, it must be replaced with	VALVE
type 105˚C or it's equivalent.

2540 specifications

Atwood Mobile Products 2540 is a standout choice in the world of portable camping devices, offering unparalleled convenience and efficiency for outdoor enthusiasts. This water heater is designed to provide instant hot water for a variety of activities, from taking a shower after a long hike to washing dishes at a campsite.

One of the main features that set the Atwood 2540 apart is its compact size and lightweight design, making it an ideal option for RVers and campers who are limited on space. Weighing in at just under 15 pounds, it can easily be transported or stored when not in use. The unit’s dimensions ensure that it fits snugly into tight spaces common in RVs and campers, providing flexibility for users.

The Atwood 2540 employs innovative technologies such as a direct vent, which enhances efficiency by ensuring that combustion air is drawn from outside the unit. This feature not only improves the performance but also minimizes the risk of exhaust fumes entering the living space. The model is designed to run on propane, which provides a dependable power source while camping in remote locations.

Another notable characteristic is the ease of use. The 2540 is equipped with an electronic ignition, eliminating the need for manual lighting. Users can simply turn on the device and enjoy hot water in seconds. The water heater also features an adjustable temperature control, allowing users to regulate the heat to their preference efficiently.

Durability is another area where the Atwood 2540 excels. Constructed with high-quality materials, this water heater is built to withstand the rigors of outdoor use while providing reliable performance. Its corrosion-resistant design ensures longevity, allowing users to enjoy many outdoor adventures without worrying about equipment failure.

In terms of safety, the Atwood 2540 includes built-in safety features such as an automatic shut-off valve and overheat protection, ensuring user confidence when operating the unit.

In summary, the Atwood Mobile Products 2540 is a remarkable portable water heater that successfully combines compactness, efficiency, durability, and user-friendly features. Its innovative technologies make it a worthwhile investment for anyone looking to enhance their outdoor experience with the luxury of hot water on demand. Whether embarking on a camping adventure or enjoying life on the road in an RV, the Atwood 2540 is a reliable companion that elevates the experience of outdoor living.