Manley Labs INTEGRATED AMPLIFIER guide

Replacing the Tubes & Setting The Bias

Setting bias is one of lifes little neccessities when you own tube amps. The other is replacing tubes. Considering how these are related we will treat both as one subject.

How long will these tubes last? We can't say for sure. Some die prematurely and some tubes last more than 30 years. The average for the tubes in the Stingray should be 4 to 5 years depending on useage. As with all tubes, their quality degrades with age. This is due to gradually decreasing cathode emission, a natural process found in all tubes.

How can I tell when I need to replace them? The output tubes (EL-84) should have their bias voltage checked on a regular basis (see page 15). Any tube thats bias reads very different from the rest should be re- adjusted, and closely monitored in the future for further large variations which would indicate it's time for replacement.The input tube and occasionally the others can have other symtoms as well. An excessive increase in noise level or distortion can indicate the need to replace a tube. Some tubes loosen up in their internal supports and become microphonic. If you tap the tube lightly it may ring through the speakers. A little is normal - a lot means "time for a new tube". A tube that has turned white inside means that air has leaked in - or (as we joke) the vacuum has leaked out. Obviously, any tube that does not light up at all is bad, too. Replace it. These tubes are not expensive, esoteric or hard to find. We always suggest that you own at least a few spare tubes.

Do I need to replace them all at once? No, at least not with these amps. Some tube amps do require that if one tube has to be replaced that a complete matched set put in. All Manley amps use individual bias trims for each output tube which allows a single tube to be replaced. Absolute best performance is achieved when the tubes are most similar. We batch them and label each tube so that in the event of a replacement you can get one from Manley of similar characteristics as the others in your amp. We need that hand drawn number on the top of the output tubes so we can supply you the optimum one.

Does the "sound" of the amp change as the tube ages? Yes, but not very much. It is just the tubes and they can be replaced. It is not like big guitar amps where tubes are replaced every 6 months for reasons of "tone". We run the tubes quite conservatively which allows a very long life and less change between old and new tubes. This is where that 4 to 5 years of use comes from. You may notice an improvement between tubes this old and new tubes depending on how critical you are. Keep in mind the sound of new tubes changes most in the first weeks of use before they can be considered "broken in". At first the sound may be a little "tight" and "direct".

Is it difficult to replace a tube? Yes, if you have trouble replacing light bulbs. It is super easy. Turn off the power. Just let the amp cool a few minutes so that you don't burn your pinkies. It helps to wiggle the tube gently rather than pulling it out straight. Even if you don't consider yourself "technical" you probably have more technical ability than your parents and they used to fix the family TV set by taking out the tubes and putting them on the tube tester at the local pharmacy. It is almost as easy to re-insert a tube. Just make sure it is correctly lined up with the socket and you dont bend a pin. You can wiggle it in too. If you had a solid state amp, it would be an unlikely repair. You would have to open it up, diagnose the bad transistors and burnt resistors, de-solder, find replacements (good luck) re-solder, and hold your breath as you turn it on. Or you could send it back, be without music for a few weeks, pay for service by the hour and get real upset when it fries again. If one transistor goes the system is dead, not so with power tubes, just limping. If you need a tube or set of tubes Manley will be happy to sell you some (matched) at a good price and if you prefer to send the Stingray back for repair or adjustment, our warranty covers about everything except tubes (6 mo. only) and abuse and we handle ground shipping back to you - usually the same week

INTEGRATED AMPLIFIER specifications

Manley Labs has a long-standing reputation for producing high-fidelity audio equipment, and their integrated amplifier is a shining example of this legacy. Catering to audiophiles who appreciate both performance and finesse, the Manley Labs Integrated Amplifier combines powerful technology with artistic design.

One of the most notable features of the Manley Labs Integrated Amplifier is its renowned vacuum tube design. Utilizing high-quality 12AX7 and 12AT7 tubes, the amplifier delivers warm, rich sound that is characteristic of tube amplification. This vintage-inspired technology creates a unique listening experience, offering dynamic range and harmonic richness that solid-state amplifiers often struggle to replicate. Additionally, the product’s advanced circuitry ensures low distortion and excellent frequency response.

An elegant chassis houses this sophisticated amplifier, enhancing both aesthetics and acoustic performance. The front panel is designed with simplicity in mind, featuring easily accessible volume controls and inputs for a variety of sources, including vinyl turntables, digital sources, and streaming devices. The dual-mono topology, where each channel has its dedicated power supply and amplification, further enhances stereo imaging and separation, resulting in a more immersive soundstage.

The Integrated Amplifier is equipped with Manley’s proprietary features, including a passive volume control and selectable equalization options. This helps users customize their listening experiences according to personal preferences or their specific audio setups. With a high output power rating, the amplifier is capable of driving a wide range of loudspeakers, making it versatile for various audio configurations.

Another key characteristic is the incorporation of modern connectivity options while maintaining a classic sound. With balanced and unbalanced inputs, as well as headphone outputs, the Manley Labs Integrated Amplifier combines traditional tube warmth with contemporary flexibility. This adaptability allows it to remain relevant in a rapidly evolving audio landscape.

Overall, the Manley Labs Integrated Amplifier is a harmonious blend of cutting-edge technology and classical appeal. Its meticulous craftsmanship, attention to detail, and performance capabilities make it a preferred choice for connoisseurs of exquisite sound quality, ensuring that music is delivered with authenticity and elegance. Whether for home listening or professional applications, this integrated amplifier stands as a testament to Manley Labs' commitment to audio excellence.