Bias Procedures

The Manley 50 Watt Amplfier is a fixed bias system that requires very little attention. If you wish to adjust or check the bias, complete the following steps. For this procedure you will need a multimeter to read millivolts (less than 2 volt range) and a small flat screwdriver.

1.Looking at the front section of the top plate of the amplifier, you can see 4 red tip jacks and 1 black tip jack. To measure the current draw of each output tube place the positive probe (red) into the red tip jack for the tube you wish to measure and the negative probe (black) in the black (GROUND) tip jack and set the meter to read 'millivolts'.

2.Each of the four (4) output tubes can have its own bias adjusted by altering its own bias adjust pot. The numbering sequence for the 4 output tubes runs from left to right, as do the corresponding tip jacks (measurement points). The bias adjust pots are located on the top side of the amplifier, therefore it will be NOT be necessary to remove the bottom cover to changing the bias. They also read left to right.

3.The first step to setting the bias is to turn on the amplifier and insure that there is zero signal input. Also, leave your loadspeakers connected as these provide an ideal load on the output. Never operate your amplifiers without a suitable load or speakers attatched. It is recommended that you leave the amplifier on long enough to ensure that the tubes have reached their stable current draw.

5.Set your meter to read VOLTS DC. You will be measuring less than 1 volt so set your meter for a low range if it is not an autoranging meter. Place the probes in the first red tip jack (negative probes remains in the black tip jack for whole biasing procedure) and adjust the first bias trim pot located on the left side top deck of the amplifier until you measure approx. 200 mVDC (0.2VDC). Since you are measuring across a 10 ohm cathode resistor, this would correspond to a 20 mA bias current.

6.If you are unable to bring the bias voltage down to 200 mV on any tube then we recommend that the tube be carefully watched or replaced.

7.Follow step five with the remaining tubes. Once they are all set, your amplifier should be in perfectoperation.

50 WATT MONOBLOCK AMPLIFIER specifications

Manley Labs has long been a respected name in high-fidelity audio equipment, and their 50-Watt Monoblock Amplifier exemplifies their commitment to exceptional sound quality and innovative engineering. Designed to provide audiophiles with a powerful, dynamic, and transparent listening experience, this amplifier is a true reflection of Manley’s dedication to craftsmanship and performance.

The 50-Watt Monoblock Amplifier utilizes a tube-driven configuration, leveraging the unique sonic characteristics of vacuum tubes. This design not only enhances the amplifier's warmth and richness but also ensures a pronounced harmonic accuracy that is often sought after in high-end audio. Manley Labs incorporates premium components, including specially selected tubes and meticulously designed circuits, to provide an audio experience that is both lush and detailed.

One of the defining features of the Manley 50-Watt Monoblock is its robust power output. The amplifier delivers an impressive 50 watts per channel, making it suitable for driving a wide range of loudspeakers with ease. Whether paired with smaller bookshelf speakers or larger floor-standing models, the amplifier maintains clarity and precision across the audio spectrum, allowing listeners to fully enjoy their favorite music.

In addition to its power capabilities, the amplifier includes a well-engineered output transformer, which plays a crucial role in ensuring optimal performance. This transformer is designed to match the impedance of various speaker loads, enabling the amplifier to maintain excellent damping factor and control over bass response while delivering harmonious mids and highs.

The 50-Watt Monoblock Amplifier is also characterized by its clean, simple aesthetic and user-friendly interface. With thoughtfully placed controls and indicators, setting up the amplifier is straightforward, even for those less experienced with audio equipment. The durable chassis is crafted to withstand the rigors of regular use, ensuring longevity while also exuding a classic elegance suitable for any listening environment.

Moreover, Manley Labs embraces modern technological advancements by including features such as an integrated power supply and an innovative cooling system, which not only enhances audio performance but also ensures reliable operation over extended periods.

Overall, the Manley Labs 50-Watt Monoblock Amplifier is a remarkable fusion of traditional tube technology and contemporary engineering, promising audiophiles an engaging listening experience with unrivaled tonal richness and detail. For those seeking a high-quality amplifier that honors both the heritage and future of audio, Manley’s offering stands out as a quintessential choice.