For EDV-35/40/45 Models

INSTALLATION INSTRUCTIONS:

1.Remove Top and Bottom Panels -

a.Remove the top louvered or radiant panel/hood assembly by pulling the assembly up and out (see Figure 2). In instances where the radiant panel is used and it is framed in with tile or other approved material, the hood must still be removed by ﬁrmly pulling it forward until it releases from the receiving brackets.

b.Remove the bottom louvered or radiant panel/hood assembly (refer to Homeowner’s Care and Operation Manual).

a.Open the latch(es) at the bottom of the glass door assembly as shown in Figure 4 (refer to Homeowners Manual).

b.Adjust glass door so that it is evenly spaced and aligned to the ﬁreplace chassis on both sides. See Figure 4.

c.Fasten the latch(es). Ensure that the latch(es) are engaged with the door’s vee-ﬂange and fully closed. See Figure 4.

Top Flange on Glass Door

Glass Door

Radiant Panels

Remove Trim Panels as shown. The trim panels will be either Louvered Panels or Radiant Panels.

Louvered

Panels

Some models will have a modesty panel in the control compartment (in front of the valve). The appearance will vary from the example shown below.

Modesty Panel

Bottom Vee-ﬂange Glass Door

Firebox Floor

Glass Door Latch

Figure 4 - GLASS DOOR ADJUSTMENT

Figure 2 - Remove Top Panel

c. Remove Bustles - Some models have bustles (as shown in Figure 3) which must be removed. If applicable, remove the top and bottom bustle by lifting them up and out.

Only Some Models

Have Bustles

Bustles

Lift Bustles Up

And Off

Figure 3 - Remove Bustles

2.Align Glass Door (see Figure 4) - Ensure the glass door assembly on the ﬁreplace is properly aligned as follows:

Note: Units with Modesty Panels - Remove the modesty panel,

if necessary, as follows: Lift the modesty panel by the tab on the panel’s right end, pull the right end of the panel away from cabinet and then pull the panel diagonally out of the corner post slots on the left side of the unit. Remove the modesty panel carefully, so that none of the wires become loose or disconnected.

3.Install Firebox Bottom Cover Panel - For Models EDV-35/40/45, see Figure 5a. For Model EDVST see Figure 5b.

	Step 1 - Remove 2 ﬁre-	Screw
	box bottom screws.	Screw
	box bottom screws.

Step 2 - Install the Firebox Bottom Cover Panel (#5 in Figure 1) using the existing screws that were removed. The top two holes on the panel align to corresponding holes on ﬁreplace.

Figure 5a - Install Firebox Cover

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

TAPD45C, TAPD35EC, TAPD35C, TAPD35SP, TAPD40SP specifications

Lennox Hearth has been a trusted name in the heating and cooling industry for years, and their range of gas and electric fireplaces is no exception. Among their impressive lineup, the TAPD35C, TAPD40SP, TAPD45C, TAPD45SP, and TAPD35EC models stand out with unique features and technologies designed to enhance both functionality and aesthetics in any home environment.

The TAPD35C is a direct vent gas fireplace that offers a contemporary design, seamlessly fitting into modern spaces. Its striking appearance is complemented by a large viewing area, which allows homeowners to enjoy a captivating flame display. With an advanced ignition system and high-efficiency burner, the TAPD35C ensures an environmental-friendly operation while providing ample warmth.

For those seeking a more spacious option, the TAPD40SP offers an extended width and a powerful heating capacity, making it ideal for larger living areas. This model is designed with a powerful venting system, which optimizes airflow and ensures consistent heat distribution. The TAPD40SP features customizable options, allowing homeowners to choose their preferred interior finishes and decorative media to match their home decor.

The TAPD45C is another excellent choice, featuring an impressive heat output combined with cutting-edge technology. It incorporates a user-friendly electronic ignition system for hassle-free operation, ensuring that the fireplace is ready to use with minimal effort. The TAPD45C also includes innovative flame modulation technology, enabling users to adjust flame height and intensity, creating the perfect ambiance for any occasion.

Similarly, the TAPD45SP carries over many of the impressive characteristics of the TAPD45C but adds an elevation feature, allowing for enhanced viewing angles and a more dramatic ambiance. This model also supports a variety of media options, including decorative stones and glass, which allow homeowners to personalize their fireplace to suit their style.

Lastly, the TAPD35EC is an electric fireplace option that combines modern innovation with appealing aesthetics. With its simple installation and remote control operation, the TAPD35EC is an excellent choice for those looking to add warmth without the complexities of traditional gas options. It features realistic flame effects and adjustable heat settings, ensuring that comfort is just a click away.

Each model in the Lennox Hearth TAPD series highlights the company's commitment to quality and performance while offering distinct features that cater to varying tastes and needs. Whether opting for gas or electric, Lennox continues to provide superior heating solutions for modern homes.