Lennox Hearth MPE-36R installation instructions Remote Control Operation

Page 7

REMOTE CONTROL OPERATION:

REMOTE CONTROL

A

POWER

 

B

 

ON/OFF

C

D

DISPLAY

ON/OFF

E

Dimmer

Brighter

FEMBERS

HEATER ON/OFF

G

TEMP. CONTROL

I

HIGH

MED. LOW

 

H

FLAME

 

 

 

 

LOWER

HIGHER

 

J

 

 

K

•When using the remote control, the power on/off switch inside the body and the wall switch (optional kit) must be on the OFF position.

Figure 6

CAUTIONS

•DO NOT USE OLD BATTERIES WITH NEW ONES.

•DO NOT USE BATTERIES OTHER THAT THE TYPE SPECIFIED (2 EA. AA).

•ENSURE BATTERIES ARE CORRECTLY INSTALLED IN REMOTE CONTROL.

The Merit Plus Electric Fireplace is provided with an Infrared light Remote Control. All functions of the fireplace can be con- trolled through the remote control. Note: The Effective range of the remote control is up to approximately 26 feet (8 meters).

The functions identified on the remote (see Figure 6) are as follows:

A.POWER BUTTON

Press once to turn on power to fireplace.

B.INDICATING LIGHT Illuminates when signal is sent.

C.LIGHT BUTTON

On/off switch for flame and ember light.

D.LIGHT ADJUSTING BUTTON (DIM) Reduces brightness of embers.

E.LIGHT ADJUSTING BUTTON (BRIGHTEN) Increases brightness of embers.

F.HEATER ON/OFF

This button will turn the heater ON and OFF

independent of the main button.

G.TEMPERATURE ADJUSTMENT BUTTON (HIGH)

Highest heat output, up to 86° F.

H.TEMPERATURE ADJUSTMENT BUTTON (MED.)

Medium heat output, up to 75° F.

I. TEMPERATURE ADJUSTMENT BUTTON (LOW)

Lowest heat output, up to 64° F.

J. FLAME ADJUSTING BUTTON (LOWER) Reduces flame intensity.

K. FLAME ADJUSTING BUTTON (HIGHER) Increases flame intensity.

Remote Control Operation Steps:

1.To control the electric fireplace by remote control, the main power on/off switch should be in the off position. This switch is located on the front left floor of firebox (see Figures 4 & 5).

2.When operating the remote control, it must be pointed at the logs inside the electric fireplace and a beep must be heard each time you press a function button. The beep lets you know the remote control is operating the function button you are pressing.

3.Remote On & Off Button - The button on the top left (see A) is the on/off power button. When pressing this button you will hear a beep, this will activates the power to the fireplace. You must then press the display button (B) to activate the lights.

Note: If the flame does not come on immedi- ately, adjust brightness and intensity (buttons E & K).

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

4.To increase the brightness, press and release the light brighten button (see E). Each time you press this button you will hear a beep, and the brightness will increase by a small amount, until the maximum brightness is achieved. To decrease the brightness, press and release the light dimming button (see D). Each time you press this button you will hear a beep, and the brightness will decrease by a small amount, until the minimum brightness is achieved.

5.HeaterButton,Toactivatetheheater,pressthe heater button (see F), then press HI (G),

MED (H), or LO (I). The heater is preset to the following temperatures:

•HIGH will shut off when room reaches approximately 86° F (30° C).

•MED. will shut off when room reaches approximately 75° F (24° C).

•LO. (Low) will shut of when room reaches approximately 64° F (18° C).

6.Flame Button - Press the Flame Adjusting Buttons to achieve a higher or lower flame intensity (see J & K).

7.To Increase Flame Brightness press and release the (K) button. Each time you press this button you will hear a beep and the brightness of the flame will increase slightly, until the maximum setting is reached. To Decrease Flame Brightness press and release the (J) button. Each time you press this button you will hear a beep and the brightness of the flame will decrease slightly, until the minimum setting is reached.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Electric Fireplace 775,172M REV. B 7/2004 For Your SafetyReport # Congratulations Table of ContentsTools and Building Supplies Normally Required Power Supply Wire SpecificationsGeneral Information Locating Your Merit Plus Electric FireplaceRight Side Framing SpecificationsFireplace Specifications Left SideElectrical Connections PRE-INSTALLATIONDetailed Installation Steps Minimum Clearances to COMBUS- TiblesBREAK-IN Period Main Power On/Off rear most switchFlame / Ember On/Off front most switch Final FinishingRemote Control Operation Brick Panel Removal Procedure MaintenanceCleaning the Glass Enclosure Panel Optional KIT HEATER/BLOWER Replacement PROCE- DureEmber Bed Bulb Replacing Light Bulbs Bulb Replacement ProcedureAccess bulbs as follows Grate120 V 1600W Wiring Diagram 120 VoltSwitch Wiring 120 Volt GroundGround Main Power Switch Wiring 240 Volt240 V 3000W Inside Outside Wall Thermostat & Wall Switch Wiring DiagramsInside Outside Optional kits, seeWall Thermostat Black White Left Side Fireplace Wall Thermostat Wiring 24 VACWhite Black Red Wall Switch Wiring 24 VACWHO Performs Corrective Action Causes TroubleshootingCAT. no Replacement PartsDescription MPE-36R712 Replacement Parts Component DiagramsAccessory Components
Related manuals
Manual 20 pages 26.75 Kb

MPE-36R specifications

The Lennox Hearth MPE-36R is an innovative gas fireplace that exemplifies both modern aesthetics and cutting-edge technology. Designed to enhance any living space, this fireplace model combines efficiency and elegance, making it a popular choice among homeowners looking to create a cozy atmosphere.

One of the standout features of the MPE-36R is its realistic flame technology. The fireplace employs advanced burner technology that produces a beautiful, lifelike flame effect, simulating the flickering light and warmth of a traditional wood-burning fire. The adjustable flame height allows users to customize the ambiance to their preference, whether for a romantic evening or a lively gathering.

The MPE-36R also boasts a high-efficiency rating, ensuring that heat is effectively distributed throughout the room without wasting precious energy. It is designed with an insulated firebox, which aids in retaining heat and maximizing output. This efficiency not only contributes to lower energy bills but also makes it an environmentally friendly option for heating your home.

Another notable characteristic of the MPE-36R is its sleek design. The fireplace features a contemporary frame that can seamlessly blend into various interior styles, from modern to traditional. Optional aesthetic enhancements, such as decorative fire glass and logs, allow homeowners to personalize the look, making it a centerpiece in any room.

Incorporating smart technology, the MPE-36R can accommodate remote and Wi-Fi controls, ensuring that users can operate it effortlessly. This feature provides the convenience of adjusting the flames, heat settings, and even the timer from the comfort of their couch or via a smartphone app.

Safety is paramount, and the MPE-36R is equipped with several features to ensure peace of mind. The fireplace includes a safety shut-off system, which automatically turns off the unit in the event of a malfunction. Additionally, the glass front remains cool to the touch, significantly reducing the risk of burns, especially in homes with children or pets.

With its combination of exquisite design, efficiency, advanced technology, and safety features, the Lennox Hearth MPE-36R is a sophisticated choice for anyone looking to add warmth and style to their home. Perfect for both new constructions and renovations, it stands out as a leading option in the world of modern gas fireplaces.
Top Page Image Contents