Lighting instructions Robertshaw 7000ERHC

EGH-85 & 95 Series 4 and PFG-6 & 7 Series 6 & 7

Lighting instructions — Robertshaw 7000ERHC

FOR YOUR SAFETY READ BEFORE LIGHTING

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.Before LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. See below.

C.Use only your hand to depress or turn the gas control knob. Never use tools. If the selector arm will not depress or move by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control, which has been under water.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

LIGHTING INSTRUCTIONS

1.Stop! Read the safety information above on this label.

2.Set the thermostat to lowest setting.

3.Turn off all electrical power to the appliance.

4.Depress gas control knob slightly and turn clockwise to OFF.

Note: Gas control knob cannot be turned to OFF unless knob is depressed slightly. Do not force.

5.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow "B" in the safety information above. If you don't smell gas, go to the next step.

6.Remove access panel located above burners.

7.Find pilot — follow metal tube from gas control. The pilot is between two burners behind the access panel.

8.Turn gas control knob counterclockwiseto PILOT.

9.Depress gas control knob and hold. Immediately light the pilot with a match. Continue to hold gas control knob in for about one (1) minute after the pilot is lit.

•If pilot can be lit without depressing gas control knob, turn gas knob clockwiseto OFF and call your service technician or gas supplier.

10.Release gas control knob. Pilot should remain lit. If pilot goes out, repeat steps 4 through 10.

•If gas control knob stays depressed after release, stop and immediately call your service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob clockwiseto OFF and call your service technician or gas supplier.

11.Replace access panel.

12.Turn gas control knob counterclockwiseto ON.

13.Turn on all electric power to the appliance.

14.Set thermostat to desired setting.

15.Replace front panel.

TO TURN OFF GAS TO THE APPLIANCE

1.Set the thermostat to lowest setting.

2.Turn off all electric power to the appliance if service is to be performed.

3.Remove front panel.

4.Depress gas control knob slightly and turn clockwise to OFF.

5.Replace front panel.

12	Part Number 550-110-031/0605

EGH-85, EGH-95, PFG-6 specifications

Weil-McLain is a recognized leader in the manufacturing of high-efficiency commercial boilers, and among its notable offerings are the PFG-6, EGH-95, and EGH-85 models. Each of these units exemplifies advanced engineering, robust performance, and energy efficiency, addressing diverse heating needs across commercial and residential applications.

The Weil-McLain PFG-6 is a powerful gas-fired boiler designed specifically for commercial applications. It features a 1,250,000 BTU input, making it suitable for larger buildings with substantial heating demands. The PFG-6 uses a heavy-duty heat exchanger for improved heat transfer and durability, ensuring dependable operation even under high-load conditions. This model is equipped with advanced controls that provide precise temperature management and system diagnostics, promoting optimal performance and energy efficiency.

The EGH-95 and EGH-85 models represent Weil-McLain's commitment to high-efficiency heating solutions. These units utilize condensing technology, recovering latent heat from flue gases to achieve efficiency ratings of up to 95% AFUE (Annual Fuel Utilization Efficiency). This high-efficiency aspect translates into substantial energy savings and reduced carbon emissions, making them an environmentally friendly choice for heating systems.

Both the EGH-95 and EGH-85 feature durable cast iron heat exchangers that not only enhance performance but also provide exceptional resistance to corrosion and wear. The EGH series also incorporates a unique multi-stage burner design, which optimizes fuel usage, reduces operational noise, and increases overall system reliability. Their compact design allows for easy installation in confined spaces, making them a versatile option for various construction layouts.

Another key characteristic shared by these models is their user-friendly control systems. With touch-screen interfaces and advanced boiler management systems, users can easily monitor performance, make adjustments, and conduct maintenance checks. This ease of use helps extend the lifespan of the equipment while ensuring efficient operation.

Overall, the Weil-McLain PFG-6, EGH-95, and EGH-85 models highlight the company's dedication to producing high-quality, efficient heating solutions tailored to meet the evolving demands of today’s building environments. Their cutting-edge technology, efficient design, and reliable performance establish Weil-McLain as a top choice for those seeking dependable heating solutions.