Advanced Menus

Separate Bass Management Settings for Stereo

You can set up a separate bass-management scheme for Stereo mode, including a different crossover frequency. While the Stage One is in Stereo mode, enter the Advanced Menu and select the SpkrConfig STEREO menu. Configure the speakers for Stereo mode as Large or Small. Now you can go to the Crossover Setup menu to select a crossover frequency for Stereo mode. This is useful if, for example, you want to run large front speakers full- range for home theater listening but set a low crossover point for low-frequen- cy fill from the subwoofer in stereo listening.

Analog Input Level

Separate input level adjustments are available for each analog input. You can reach them from the Setup page on the remote control. Pressing the Input Gain +/- will bring up the analog input level adjustment. Choose a dynamic passage from the analog source and turn the analog input gain up until Clipping is indicated in the top left-hand corner of the front-panel display. Turn the gain down again in half-decibel steps until the clipping indicator goes off.

Separate Video Input Switching

The Stage One allows for separate selection of audio and video input sources. A Separate Video Switching page is available from the remote con- trol’s Adjustments page. Selecting any of the available inputs will switch to the video signal for that input while leaving the audio input as previously selected.

System Lock

In certain situations it may be desirable to "lock" the system. Once you have your Stage One set up the way you want it, you can prevent accidental alter- ations by locking it, which prevents permanent changes to channel balances or the Advanced Menus. When locked, the Stage One will not let anyone into the Setup or Advanced Menus. (On-the-fly level and balance adjustments are still permitted, but these settings are not saved.)

To lock the Stage One (or unlock it if it is already locked), turn the preamp off. Then press the front-panel Enter and Mute buttons simultaneously, and while keeping these buttons depressed, press the Power button. This will toggle the Stage One between Locked (indicated by a capital L in the front-panel dis- play) and Unlocked (indicated by a capital U in the front panel-display) mode. Once you have the processor in the correct mode, you can release all but- tons. The mode indication will remain on the front panel display until you turn the Stage One on again.

Front/Rear Balance

You can adjust front-to-rear balance temporarily by pressing the Up and Down buttons on the remote. (This option is available only in modes that use the surround channels.) Shifting the balance toward the surround channels using the Down button will reduce the volume of the front channels. Moving the bal- ance toward the front channels using the Up button will lower the volume of the surround channels. This is a temporary adjustment, so the next time a mode is loaded, the balance will be reset to the center position. If you find that you must continually readjust the front-to-rear balance, it may indicate that your default channel levels are not set properly.

Left/Right Balance

You can temporarily adjust the left/right balance in Stereo mode using the Left and Right buttons on the remote control. Moving the Balance toward the left will lower the volume of the right channel. Moving the Balance toward the right will lower the volume of the left channel. This is a temporary adjustment, so the next time a mode is loaded, the balance will be reset to the center posi- tion. If you find that you must constantly adjust the balance, it may indicate that your default channel levels are not set properly.

Enter the Advanced Menus by pressing the Advanced Menu button on the remote. Use the Up and Down buttons to scroll through the menu list. Press the OK button to enter the desired menu when it appears on the bottom line of the front-panel display. Use the Left and Right buttons to adjust settings. Once you have edited a particular menu setting, pressing Menu or the OK button again will bring you back to the Advanced Menu selection screen, and pressing Advanced Menu will exit the Advanced Menus. (The Advanced Menus can also be accessed from the front panel by using the Stage Manager and Enter button.)

Levels

The initial setup procedure defines a single channel balance for all modes. Although this setting should be correct for most of the basic surround modes, you can trim the balances individually for each mode from this menu. Once set for a particular mode, customized channel levels will be loaded automati- cally whenever that mode is selected. It should be noted that changing levels in this menu will only change the settings for that particular mode and will not affect the levels for other modes as they were set in the initial setup procedure.

Scroll Test Tones

The default setting is No, which will cause the calibration signal to stay in a particular channel until you tell it to change. Setting this to Yes will cause the calibration signal to rotate from channel to channel every two seconds when you are in the Level Settings menu.

Test Tone OFF

The default setting is No. If you set this to Yes, there will be no calibration sig- nals when you enter the Setup Mode. This enables you to use test signals from an external source for channel balancing.

THX ULTRA2 specifications

The Klipsch THX Ultra2 system is a premium home theater speaker system that epitomizes high-fidelity audio performance. Designed for enthusiasts seeking a cinematic experience in their own homes, this system excels in delivering powerful, clear sound across a wide frequency range.

One of the standout features of the THX Ultra2 system is its compliance with the THX Ultra2 certification. This certification ensures that the speakers meet rigorous performance standards, making them capable of delivering an immersive audio experience akin to that found in commercial theaters. The system is engineered to produce dynamic range and low-distortion sound at high volume levels, which is crucial for recreating the explosive effects of modern films.

The THX Ultra2 system typically comprises several key components: main speakers, satellite speakers, and subwoofers, all designed to work in harmony. The main speakers are equipped with Klipsch's signature horn-loaded technology, which allows for increased efficiency and better high-frequency response. This design means that listeners can enjoy crisp, clear dialogue and intricate details in music without strain, even at higher volume levels.

In addition to its horn-loaded design, the THX Ultra2 system includes high-performance woofers made from rigid materials. These woofers add depth and richness to the bass response, ensuring that explosions, music, and ambient sounds are felt as much as they're heard. The subwoofer is specifically designed to provide tight, impactful bass that extends down to lower frequencies, ensuring a full-range listening experience.

Klipsch also incorporates a unique technology called "Tractrix Horn," which enhances sound dispersion and efficiency. By directing the sound precisely toward the listener, this technology minimizes distortion and improves clarity, especially in larger rooms where sound can often dissipate.

Another notable characteristic of the THX Ultra2 system is its elegant design, which integrates seamlessly into any home decor. The speakers often feature a sleek finish that not only looks sophisticated but also minimizes resonance, further enhancing audio quality.

In conclusion, the Klipsch THX Ultra2 speaker system represents a pinnacle in home audio technology. With its THX certification, innovative speaker design, and superior performance across music and movies, it provides an unparalleled entertainment experience, making it a top choice for audiophiles and home theater enthusiasts alike. Whether you are watching movies or listening to your favorite albums, the Klipsch THX Ultra2 fully captures the essence of high-quality sound.