Fasten cabinet to a structural support | Honeywell F111 Series 3

F111 (SERIES 1,2,3) IN CEILING MEDIA AIR CLEANER

TOP OF METAL CABINET

THREADED

ROD

JAM

NUT

CHAIN

EYEBOLT

JAM NUT 3/8 IN. X 16T

HEX BOLT

LOCK

WASHER

CAUTION

• This installation to be performed only by a qualified

installer.

• All wiring to comply with local electrical codes.

• Disconnect power to air cleaner at fuse or breaker

before beginning work. Failure to do so can result in

shock hazard endangering equipment and personal

safety of installer.

• Only one air cleaner can be connected to a remote

switch

OR USING OPTIONAL "Z" BRACKETS

TOP OF METAL CABINET

"Z" BRACKET (4)

NOTE:

FASTEN SECURELY TO STRUCTURAL

SUPPORT SYSTEM, I.E. BAR JOIST,

CONCRETE SLAB OR TIMBER FRAMING.

BOTTOM FLANGE AGAINST	CEILING
UNDERSIDE OF TEES	TEE
	BOTTOM VIEW OF
	UNIT WITHOUT
	LID ASSEMBLY

1.	Disconnect power to air cleaner.
2.	Mount 4” x 4” outlet box at desired remote location.
3.	Attach 3/4” extension ring to outlet box.
4.	Run five conductor, color-coded, 18-gauge wires from
	the remote switch location to the air cleaner.
5.	Use three wire nuts to connect three color-coded, lead
	wires on the remote switch to three color-coded wires
	from the air cleaner. (Red, Blue, Violet)
6.	Use one wire nut to connect white color-coded, lead
	wire from the air cleaner to single color-coded wire from
	the power supply. (White)

BLACK

M10892

Fig. 5. Fasten cabinet to a structural support.

IMPORTANT

Do not touch the pleated filter media. Handle only the filter frame to prevent damage to the filter media.

11.Remove CPZ™ sorbent modules (select models) from their packaging and install one module into each cavity.

12.For Series 1 only. Be sure the fastener tabs are facing downward and fasten them.

13.For Series 2 and 3 only. Be sure both catches are turned down and filter rests firmly on catches.

14.Install the prefilter in the air cleaner lid. Position the metal screen mesh so it is facing upward when the lid is closed.

Remote 3 Speed Wall Switch (3 Speed Models only)

The 190097C Remote Wall Switch Assembly allows control of the F111 model air cleaners from a a location separate from the air cleaner. The assembly includes a remote switch with an outlet box cover, outlet box, extension ring, and a wire harness. Wiring to connect the remote switch and air cleaner must be furnished separately.

A100001

Fig. 6. Wiring 3-Speed Remote Switch

7.Connect the ground wire from the power supply to a ground stud of the outlet box.(Green)

8.Connect the ground wire from the air cleaner to the ground stud of the outlet box.(Green)

9.Use one wire nut to connect the black color-coded, lead wire on the remote switch to the black color-coded wire from the power supply.

10.Fold wires into box and mount remote switch on outlet box. Leave switch in OFF position.

11.On the air cleaner remove two screws on wiring com- partment cover and open

12.Run five conductor, color coded, 18 gauge wires from the remote switch through the air cleaner access open- ing into the wiring compartment. Strip ends of remote switch lead wires

13.Connect three wires on air cleaner to remote switch lead wires with wire nuts following color code used at remote switch. (Red, Blue, Violet)

68-0198-2 Revised 5-09

F111 Series 3 specifications

The Honeywell F111 Series 3 is a notable aircraft in the realm of military aviation, primarily designed for ground attack and tactical strike missions. A derivative of the original F-111 Aardvark, the Series 3 variant exemplifies advanced engineering and technological innovations that enhance its combat capabilities.

One of the standout features of the F111 Series 3 is its unique variable-sweep wing design, which provides exceptional versatility in various flight conditions. This design allows the wings to adjust their angle during flight, optimizing performance for both high-speed intercepts and low-level tactical missions. As a result, the F111 can operate effectively at a wide range of speeds and altitudes, giving it a tactical edge over its peers.

Equipped with advanced avionics systems, the F111 Series 3 incorporates cutting-edge navigation and targeting technologies. Its onboard radar and electronic warfare systems enable it to detect and track enemy targets while remaining largely undetected. The aircraft can carry a diverse array of munitions, including precision-guided bombs and air-to-ground missiles, further enhancing its strike capabilities. The ability to deliver payloads with pinpoint accuracy makes it a formidable weapon on the battlefield.

Another key characteristic of the F111 Series 3 is its advanced cockpit design. The aircraft features a tandem two-seat configuration, which allows for seamless communication and coordination between the pilot and weapons systems officer. The cockpit is equipped with modern displays and controls that improve situational awareness and streamline operations.

In terms of durability, the F111 Series 3 is engineered to withstand harsh combat conditions. Its robust airframe is constructed to endure the stresses of high-speed flight and combat maneuvers, ensuring mission success even in challenging environments. Additionally, the aircraft's engines are designed for performance reliability, providing ample thrust while maintaining fuel efficiency.

Overall, the Honeywell F111 Series 3 stands out as a versatile and formidable platform in military aviation. With its advanced features, technologies, and characteristics, it continues to play a significant role in modern air operations, embodying the innovation and capabilities expected from contemporary military aircraft.