Honeywell 6160V setup guide General Information, Keypad Displays and Leds, Function KEY Labels

K0022V3 3/09 Rev. A

ADEMCO 6150V & 6160V

Voice Remote Keypads

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The ADEMCO 6150V and ADEMCO 6160V are addressable remote keypads designed for use with ADEMCO control panels and provide the following features:

• Backlit Display	• Voice Chime
• Programmable Function Keys	• Voice Status
• Built-in Sounder	• Message Center

•Supervised by control panel (if supported)

Notes:

•When used with the ADEMCO VISTA-15P/VISTA- 20P control panels, address 16 must be assigned to the first keypad. Additional keypads must be assigned to address 17 – 23. Refer to Setting The Keypad Options.

•Keypad keys are continuously backlit for convenience.

•Permanent display backlighting is an option on some controls (refer to control panel’s instructions for details).

•Voice Chime should only be enabled when used with control panels that support the "chime by zone" mode (e.g., VISTA-15P/VISTA-20P). This mode must be enabled at the control panel. Refer to the control panel's installation and setup guide for information on how to program the chime mode.

•Use only zone descriptors supported by this keypad. If using zone descriptors not supported by this keypad, you must turn voice status and voice chime off. Table 1 is a list of applicable zone descriptors and index entries. Refer to the control panel’s installation and setup guide for information about how to program zone descriptors.

•For the 6160V ONLY, supervision must be enabled for commercial fire installations.

UL NOTE: ADEMCO 6150V cannot be used for commercial fire applications.

KEYPAD DISPLAYS AND LEDS

The keypads have the following display features:

Model	Fixed	2-Line	2-Digit	Custom
	Word	Alpha	Zone	Zone
	Display	Display	Identifier	Descriptors
6150V	X		X
6160V		X		X

The following table identifies the keypad’s LEDs and associated functions:

LED	Function
ARMED	Lights red when the system is armed in any mode.
READY	Lights green when the system is "ready" to be
	armed.
MESSAGE	Flashes red when message waiting or lights red
	(steady) when in record mode.

PROGRAMMABLE FUNCTION KEYS

The keypad's programmable function keys [A, B, C] are normally used for keypad panic functions, but they can be programmed for other special functions instead. If they are programmed for other special functions, the associated keypad key pairs still provide the respective panic alarm (if programmed). Refer to the control panel’s Installation & Setup Guide for details.

Function	Equivalent Key Pairs
Keys
A	[1] and [*]
B	[*] and [#]
C	[3] and [#]
D	NONE

•Function keys must be held down for at least 2 seconds to activate the programmed function.

•If functions other than panics are assigned to the programmable function keys, programmed panics must be initiated by pressing the programmed key pair.

FUNCTION KEY LABELS

A set of adhesive-backed labels with some typical function symbols (i.e., fire, police, personal emergency, etc.) is provided. These labels can be placed on or next to the keys to identify each key's function for the end user (as determined by the capability and programming of the control panel; refer to the installation and setup guide for the control panel).

BA	ARMED	RECORD1 FF	VOLUME2 AWAY	3PLAYSTAY
	MESSAGEREADY	4 MAX	5 TEST	6 BYPASS	SIDE
		7 INSTANT	8 CODE	9 HIME	VIEW
C	MIC	STATUSREADY	0VOICE	FUNCTION#
D
		MOUNTING RELEASE SNAPS				-V1
						001
	(Remove case back by pushing up the 2 "snaps" along
						6160V-
	the keypad's bottom edge and pulling the case apart.)

WIRING AND INSTALLATION

Keypads can be surface mounted using drywall anchors or to a single- or double-gang electrical box.

1.	Remove the case back by pushing up the two "snaps"
	along the keypad’s bottom edge and pulling the case
	apart. See diagram above.
2.	Route wiring from the control panel through the
	opening in the case back.
3.	Mount the case back to a wall or electrical box.
4.	Wire directly from the keypad’s terminal block to
	the terminal block on the control board. (See Wiring
	Table that follows.) Use only 16-24 AWG wire.
		Wiring Table (All Keypads)
	Keypad		Control Panel	Wire Color
	G		Data In	Green
	–		– Aux Pwr (GND)	Black
	+		+ Aux. Pwr	Red
	Y		Data Out	Yellow
5.	Re-attach the keypad to the case back.
6.	Remove clear protective film from LEDs (6160V
	only).