White Rodgers 1F59-13 Installation, Select Thermostat Location, Route Wires to Location

Page 2

INSTALLATION

SELECT THERMOSTAT LOCATION

Proper location insures that the thermostat will provide a com- fortable home temperature. Observe the following general rules when selecting a location:

1.

Locate thermostat about 5 ft. above the floor.

2.

Install thermostat on a partitioning wall, not on an outside

 

wall.

3.

Never expose thermostat to direct light from lamps, sun,

 

fireplaces or any temperature radiating equipment.

4.

Avoid locations close to windows, adjoining outside walls, or

 

doors that lead outside.

5.

Avoid locations close to air registers or in the direct path of

 

air from them.

12” hole for thermostat wire

Stout cord with 6” chain attached

Baseboard

strip moulding

14” guide hole for sighting

Quarter round

removed

Approximately 5 feet from floor

6.

Make sure there are no pipes or duct work in that part of the

 

wall chosen for the thermostat location.

7.

Never locate thermostat in a room that is warmer or cooler

 

than the rest of the home, such as the kitchen.

8.

Avoid locations with poor air circulation, such as behind

 

doors or in alcoves.

9.

The living or dining room is normally a good location,

 

provided there is no cooking range or refrigerator on oppo-

 

site side of wall.

ROUTE WIRES TO LOCATION

1.If an old thermostat is being replaced and is in a satisfactory location, and the wiring appears to be in good condition, use existing wiring. If in doubt, re-wire.

2.If a new location is chosen or if this is a new installation, thermostat wire must first be run to the location selected. All wiring must conform with local and national electrical codes and ordinances.

3.Probe for obstructions in partition before drilling 12” hole in wall at selected location. Take up quarter round and drill a small guide hole for sighting (see fig. 1). From basement, drill 34” hole in partition floor next to guide hole. In houses without basements, drill 12” hole through ceiling and into partition from above (see fig. 1).

4.Through this hole drop a light chain, or 6” chain attached to a strong cord. Snag cord in basement with hooked wire. In houses without basements, drop cord through hole in ceiling and down partitioning; snag cord at the thermostat location.

5.Attach thermostat wire to cord and pull wire through hole in wall so that 6” of wire protrudes.

ATTACH THERMOSTAT BASE TO WALL

1.Remove thermostat cover. Pull wires through opening near center of thermostat base and connect wires under terminal screws (see WIRE THERMOSTAT TO SYSTEM).

2.Push excess wire into wall and plug up hole with fire-resistant material, such as fiberglass insulation, to prevent drafts from affecting thermostat operation.

3.Place thermostat base over hole in wall for wires and mark mounting hole locations on wall.

4.Drill mounting holes.

34” hole in floor of partition

Hooked wire for snagging chain

Figure 1. Routing thermostat wires

5.Fasten thermostat base loosely to wall using two mounting screws (see fig. 2). Place a level against bottom of base, adjust until level, and then tighten mounting screws to secure base (leveling is for appearance only and will not affect thermostat operation). If holes in wall are too large and do not allow you to tighten base snugly, use plastic screw anchors to secure base.

Screw

Anchors

Mounting

Hole

G

O

 

Y

Mounting

B

 

Hole

Figure 2. Mounting thermostat base to wall

!CAUTION

Take care when securing and routing wires so they do not short to adjacent terminals or rear of thermostat. Shorted wires may result in personal injury and/or property damage.

2

Image 2
Contents Specifications WHITE-RODGERSINSTALLATION & Operation InstructionsPrecautions DescriptionSelect Thermostat Location InstallationRoute Wires to Location Attach Thermostat Base to WallWire Thermostat to System Attach Setpoint Knob and CoverCompressor Short Term Cycle Anticipation AdjustmentOperation Protection

1F59-13 specifications

The White Rodgers 1F59-13 is a state-of-the-art programmable thermostat designed for residential heating and cooling systems. With a sleek design and user-friendly interface, this device serves as a vital tool for homeowners who seek to optimize their comfort while efficiently managing energy consumption.

One of the main features of the 1F59-13 is its programmable functionality, allowing users to customize heating and cooling schedules according to their daily routines. This scheduling capability helps homeowners save on energy costs, as the thermostat can automatically adjust the temperature when occupants are away or asleep. The device supports 5-2 day programming, which enables different settings for weekdays and weekends, enhancing flexibility.

In terms of technology, the 1F59-13 utilizes advanced temperature control algorithms that ensure precise temperature regulation. The thermostat can manage both conventional and heat pump systems, providing versatility for various heating and cooling configurations. Additionally, it is equipped with a digital display that presents clear, easy-to-read information, such as the current temperature and programmed settings.

Another significant characteristic of the White Rodgers 1F59-13 is its compatibility with a wide range of HVAC systems. This feature simplifies installation and usage, allowing the device to work seamlessly with most conventional forced air systems, gas systems, and heat pumps. Furthermore, its battery backup ensures that the programmed settings are retained during power outages, offering peace of mind to users.

The thermostat also includes an intuitive user interface, comprised of clearly labeled buttons that facilitate easy navigation through the settings. Users can easily switch between modes, adjust the temperature, and access the scheduling features with minimal effort.

In terms of energy efficiency, the 1F59-13 supports energy-saving features that alert users when it's time to change the air filter or if there are issues with the HVAC system, thereby improving overall home comfort. This proactive capability helps homeowners maintain their systems, ensuring optimal performance and longevity.

In summary, the White Rodgers 1F59-13 programmable thermostat is an excellent solution for homeowners looking to enhance their comfort and energy efficiency. Its programmable functionality, advanced temperature control, compatibility with various HVAC systems, and user-friendly interface make it an invaluable addition to any home. This device exemplifies reliable technology in home climate control, ensuring a pleasant living environment year-round.