Whirlpool 318686-000 installation instructions Adjusting the Energy Smart Module/Operational Modes

Page 11

Adjusting the Energy Smart® Module/Operational Modes

Water Temperature Adjustment

IMPORTANT: Before attempting to adjust the thermostat, read the “Water Temperature Regulation” section on page 10. If the instructions are not clear, contact a qualified person.

The water temperature can be adjusted from 80° F to 150° F. Use the Up and Down Buttons

to set the

desired temperature.

 

Operating Mode Descriptions

The operating modes can be changed by touching the desired mode icon on the Energy Smart® Module (See Figure 10). NOTE: All buttons on the Energy Smart® Module are touch sensitive and require only a light touch to actuate.

Figure 10: Energy Smart® Module (ESM)

Operational

Mode Buttons

ENERGY SMART® - This mode is used to save energy by monitoring usage and adjusting the set point to match the water draw usage pat- tern (Temperature set point can be changed).

STANDARD - Pressing this button will allow the temperature set point to be set directly.

Element

Functioning

Icon

ENERGY

STANDARD VACATION

GRID

SMART

 

ENABLED

F

ELEMENT ALERT GRID LOCK

Water

Temperature

Set Point

VACATION MODE - The control- ler adjusts the water temperature to approximately 600F. This mode is recommended when the water heater is not in use for a long period of time. This mode minimizes en- ergy consumption and prevents the water heater from freezing during cold weather.

GRID ENABLED - Pressing this button will enable or disable a re- quest for grid control (see page 13).

Temperature

Up (Increase)

Button

Fahrenheit/ Celsius Temper- ature Display Button

°F/°C

Control Panel

Lock Icon

Temperature

Down (Decrease)

Button

LCD Display Panel Lock Button

°F/°C

ELEMENT

CONTROL PANEL LOCK - Holding this button for more than 3 seconds switches the lock mode on or off.

When the User Module is locked, a symbol and “Lock” text will be visible on the display.

0F/0C - This button switches the display to show the set temperature in Fahrenheit or Celsius.

Fault condition will display an “E” followed by two digit fault code with Alert Icon flashing. (see diagnostic code chart page 17).

Element Functioning Icon - indicates power is on at either upper or lower element circuits and both are work- ing properly.

Energy Smart®

Module (ESM)

Electronic Thermostat (ET)

NOTE: The Electronic Thermostat (ET) is designed so that it may control the water heater without the Energy Smart® Module (ESM) being operated, see page 12.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Instructions Your safety and the safety or others are very important Water Heater SafetyImportant Safety Instructions Unpacking the Water Heater Installing Your Water HeaterConsumer Information Consumer ResponsibilitiesSite location Location RequirementsWater System Piping Piping InstallationExplosion Hazard Temperature and Pressure Relief ValveClosed System/Thermal Expansion Discharge Line Temperature & Pressure Relief ValveSolar Installation Electrical RequirementsRed Electrical Connections Installation ChecklistWater Heater Location Water System PipingWater Heater Start-Up Water Temperature RegulationSafety Shut-Off Operating Your Water HeaterOperating Mode Descriptions Adjusting the Energy Smart Module/Operational ModesWater Temperature Adjustment Overriding The Energy Smart Module ESM Diagnostic LED LightElectronic Thermostat Smart Grid Control Where AvailableSmart Grid Technology Stacking Operational ConditionsAnode Rod/Water Odor Water Heater SoundsReplacing the Anode Rod Maintenance of Your Water HeaterTemperature and Pressure Relief Valve Draining and FlushingHeating Element Replacement E12 Diagnostic Code Chart Energy Smart Module ESME10 E11E51 with an alert Icon flashing Diagnostic Code Chart Electronic Thermostat ET 10, 11 or 12 Flashes Problem Possible Causes Corrective Action Troubleshooting ChartRepair Parts List Repair Parts IllustrationRepair Parts Branch Circuit Sizing Guide Thermostat Wiring Diagram

318686-000 specifications

The Whirlpool 318686-000 is a highly regarded appliance part that plays an essential role in modern kitchen functionality. Designed with the user in mind, it boasts several features and technologies that enhance its performance and reliability.

One of the primary characteristics of the Whirlpool 318686-000 is its compatibility with a wide range of Whirlpool ovens and ranges, making it a versatile choice for many households. This part is commonly known as the surface element, which provides the necessary heat for cooking a variety of dishes. Its design ensures even heat distribution, which is vital for achieving perfectly cooked meals every time.

The Whirlpool 318686-000 is engineered with durability in mind. Constructed from high-quality materials, this part is built to withstand the daily stresses of cooking while maintaining its performance. This longevity translates into reduced replacement costs and increased satisfaction for users, making it an economical choice for homeowners.

In terms of safety, the Whirlpool 318686-000 features advanced technology to minimize risks associated with cooking. It typically includes integrated thermal protection, which helps prevent overheating. This feature not only prolongs the lifespan of the component but also ensures a safer cooking environment for users.

Installation of the Whirlpool 318686-000 is designed to be user-friendly. Homeowners can replace this part without needing specialized tools or professional assistance, allowing for convenient maintenance. This ease of installation is especially appealing for those who prefer a DIY approach to home repairs.

Efficiency is another hallmark of the Whirlpool 318686-000. The design optimizes energy consumption, allowing users to cook efficiently while saving on utility costs. The element heats up quickly, reducing wait times and enhancing overall cooking experiences.

Whirlpool is a brand synonymous with innovation, and the 318686-000 reflects this commitment to excellence. The part combines modern technology with practical design, ensuring it meets the needs of contemporary cooking. With its blend of durability, safety, efficiency, and ease of use, the Whirlpool 318686-000 is an essential addition to any kitchen, providing reliable performance that cooks can depend on for years to come. Whether replacing a worn-out part or upgrading to enhance cooking capabilities, this surface element is a top choice for Whirlpool appliance users.
Top Page Image Contents