SonicWALL TZ 180 Appendix B Safety Instructions and Regulatory Information, Cable Connections

Page 27

Appendix B: Safety Instructions and Regulatory Information

Regulatory Model/Type

Product Name

APL17-048

TZ 180

Mounting the SonicWALL

•Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended.

•Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers

•The included power cord is intended for use in North America only. For European

Union (EU) customers, a power cord is not included.

•Ensure that no water or excessive moisture can enter the unit.

•Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended.

•Consideration must be given to the connection of the equipment to the supply circuit and the effect of overloading the circuits has minimal impact on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern.

Lithium Battery Warning

The Lithium Battery used in the SonicWALL security appliance may not be replaced by the user. Return the SonicWALL security appliance to a SonicWALL-authorized service center for replacement with the same or equivalent type recommended by the manufacturer. If, for any reason, the battery or SonicWALL security appliance must be disposed of, do so following the battery manufacturer's instructions.

Cable Connections

All Ethernet and RS232 (Console) cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWALL is located.

Power Supply Information

If the power supply is missing from your SonicWALL product package, please contact SonicWALL Technical Support at 408-752-7819 for a replacement. This product should only be used with a UL listed power supply marked “Class 2” or “LPS”, with an output rated 12 VDC, minimum 1.66 A.

Page 26 Appendix B: Safety Instructions and Regulatory Information

Page 26 Page 28
Image 27
Page 26 Page 28
Contents SonicWALL TZ Getting Started Guide SonicWALL TZ 180 Getting Started Guide Document Contents This Section Completing Pre-Configuration TasksSystem Requirements Check Package Contents Networking Information Obtain Configuration InformationPlease record Obtain Internet Service Provider ISP Information8 Obtain Internet Service Provider ISP Information Registering Your SonicWALL Registering with MySonicWALL.com Enter your authentication codeConnecting for Initial Setup Apply Power Connect your Computer to the LAN 1 Port Connect WAN Port to the InternetVerify WAN / LAN Connection Running the Setup Wizard Log into the SonicWALL TZ Unable to See the Setup Wizard? If you see the login screen, but not the Setup WizardIf you do not see the login screen or the Setup Wizard SonicWALL TZ 180 Setup Wizard Verify Management Interface Connectivity Verify WAN Internet Connectivity Having Trouble Connecting to the Internet?Connecting to Your Network Connect and Configure Your Network OPT SonicWALL TZ 180 Front PanelSonicWALL TZ 180 Back Panel Feature DescriptionWindows NT Appendix a Configuring Dhcp IP AddressingWindows XP WindowsMounting the SonicWALL Appendix B Safety Instructions and Regulatory InformationLithium Battery Warning Power Supply InformationInformationen zur Stromversorgung Weitere Hinweise zur MontageHinweis zur Lithiumbatterie KabelverbindungenFCC Part 15 Class B Notice Canadian Radio Frequency Emissions StatementDeclaration of Conformity Vcci Statement Regulatory Information for Korea Trademarks Copyright NoticeSonicWALL TZ 180 Getting Started Guide 32 Notes SonicWALL, Inc
Related manuals
Manual 40 pages 19.53 Kb Manual 38 pages 55.88 Kb
Top Page Image Contents