Viking K-827, KK825, KK827, K-825, K-823, KK823 service manual Bushings on, Name of Part

Page 5

4.Remove head from pump. Do not allow idler to fall from idler pin. Tilt top of head back when removing to prevent this. Avoid damaging head gasket set, all gaskets are required to maintain end clearance.

5.Remove idler and bushing assembly. If idler bushing needs replacing, see “Installation of Bushings” page 9. If further disassembly is required pump must be separated from coupling. Refer to “Disassembly: Coupling,” on page 6, before proceeding with Step 6.

6.After inner magnet is removed then remove key and external retaining ring from the shaft. Rotor and shaft may now be extracted by tapping on end of the shaft with a soft face hammer (if a soft faced hammer is unavailable a regular hammer may be used with a piece of hardwood).

7.Mark the location and orientation of the Balance plate before removing by pulling out. (The balance plate may not be removable in the 825 series).

The casing should be examined for wear, particularly in the area between ports. All parts should be checked for wear before pump is assembled.

When making major repairs, such as replacing a rotor and shaft, it is advisable to also install a new head and idler pin, idler and bushing, and casing bushings. See “Installation of

Bushings” on page 9.

Clean all parts thoroughly and examine for wear or damage. Check bushings, idler pin and balance plate; replace if necessary.

ITEM

NAME OF PART

ITEM

NAME OF PART

ITEM

NAME OF PART

 

 

 

 

 

 

1

Bracket Gasket - Primary

10

Casing

19

Head Gasket

2

Bracket Gasket

11

Capscrew for Inner Magnet

20

Idler Pin

3

Orifice

12

Lockwasher

21

Head & Pin

4

Bracket

13

Washer

22

Pipe Plug

5

Capscrews for Casing

14

External Retaining Ring

23

Capscrews for Head

6

Casing Gasket

15

Key

24

Gaskets for Relief Valve

7

Bracket Bushings

16

Rotor & Shaft

25

Relief Valve

8

Balance Plate (Maybe Not in 825)

17

Idler Bushing

26

Capscrews for Relief Valve

9

Pipe Plugs

18

Idler & Bushing

 

 

FIGURE 5

K & KK Mag Drive Pump

SECTION TSM 845

ISSUE F

PAGE 5 OF 14

 

 

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Introduction ContentsOr death Safety InformationSpecial Information MaintenanceRefer to Figures 4, 5 & 6 for names of parts Disassembly PumpName of Part Bushings onSeries MD-C80 Coupling Disassembly CouplingCapscrews 4 req’d Assembly Disassembly & Assembly of MD-C Series Bearing HousingGasket Table Assembly PumpAssembly Coupling Installation of BushingsPump Rotation Adjusting Head Gasket END ClearancePressure Adjustment Assembly Relief ValveDisassembly Relief Valve Pressure Relief ValvePump Information TroubleshootingWarranty

K-823, KK823, K-827, K-825, KK825 specifications

Viking KK827, K-827, K-823, KK825, and KK823 are notable models from the Viking lineup, celebrated for their cutting-edge technology, robust characteristics, and remarkable performance. These vehicles exemplify a blend of sophisticated engineering and practical design, catering to a broad spectrum of user needs, from rugged outdoor tasks to urban mobility.

One of the standout features of the Viking KK827 is its powerful engine, designed to deliver exceptional torque and horsepower. This translates into impressive towing capacities, making it a popular choice for those who require a vehicle capable of handling heavy loads. The K-827 and K-823 models, on the other hand, focus on efficiency and agility, featuring lighter frames that enhance maneuverability while still providing substantial payload capabilities.

Technologically, these models integrate advanced systems that elevate the driving experience. Many of them are equipped with state-of-the-art navigation and infotainment systems, providing drivers with real-time information and entertainment options. Safety features are also paramount, with advanced braking systems, traction control, and rollover protection systems ensuring a secure driving environment.

The KK825 model showcases enhanced off-road capabilities, equipped with all-terrain tires and improved suspension systems that allow it to conquer varying landscapes effortlessly. These vehicles are built to withstand challenging conditions, featuring durable body designs and protective undercarriages to guard against rocks, mud, and debris.

In terms of interior comfort and utility, the Viking models do not disappoint. Spacious cabins, high-quality materials, and configurable seating arrangements cater to both passenger comfort and cargo versatility. Whether it's a trip through rugged trails or daily commutes, users can expect a comfortable ride complemented by ample storage space.

The Viking KK series stands out not just for its specifications and features but also for its commitment to sustainability. Many of the models employ eco-friendly technologies aimed at reducing emissions and enhancing fuel efficiency. This eco-conscious approach appeals to users looking for vehicles that align with modern environmental standards.

Overall, Viking KK827, K-827, K-823, KK825, and KK823 represent a significant advancement in the realm of versatile utility vehicles. With their robust features, innovative technologies, and superior performance, they have carved out a niche that satisfies a diverse array of needs, whether for work or leisure. These models continue to exemplify the Viking brand's dedication to quality and functionality, making them a trusted choice among discerning users.
Top Page Image Contents