Linear 2171-4 installation instructions Encore Multi-Room Audio, Distribution System, IR Emitter

Encore Multi-Room Audio				1.	PRODUCT DESCRIPTION	2. EMITTER DETAILS
				The Model 2171-4 Single-head Infrared (IR) Emitters are supplied in
Distribution System							Model 2171-4 IR Emitter			Side View
				a package of four and are used with the Linear Encore Multi-Room
2171-4				Audio Distribution System, ENC-SIWP source input or ENC-LIWP				NOTE: White side		1/4"
							3.5 mm mono
				local input wall plates. These generic emitters can also be used		(+)		stripe is positive (+)
							mini plug
										Top View
				with Linear’s video hubs, 2100A and 2010 in-wall interface, or with
										5/16"
Single-head				a 5500 series IR enabled modulator connected to a video hub.
				Each emitter contains a tiny infrared LED housed in a miniature,			(–)
IR Emitter								7 FT	3 FT	9/16"
				injection molded plastic shell. The emitters have adhesive backing					The emitter's shell, though dark in
(4-pack)				for mounting. An emitter can be installed directly on the IR sensor			Internal
				window of the controlled source component or in a suitable nearby			IR Emitter		appearance, is transparent to
Installation						High		Low
				location.					handheld remote controls will pass
									infrared light. Commands from
Instructions				An IR emitter repeats IR remote control signals received at a room		Output		Output	through the emitter case to the
						Side		Side
									source component.
				station keypad or IR target from a handheld IR remote control.
				When an IR signal is detected at a target, the signal is sent to the			Emitter	Clear adhesive layer
				IR OUT jacks on the wall plates or device. An IR emitter connected
								(Replace, if necessary,
							Shell
				to the IR OUT jack, repeats the same IR signal to the source				with a short piece of
	USA & Canada (800) 421-1587 & (800) 392-0123
								2-sided supplied)
				component. This allows IR remote control of source components
	(760) 438-7000 - Toll Free FAX (800) 468-1340					Mini-wire
		www.linearcorp.com		that are located away from the IR target.			Lead
3. ATTACHING EMITTER TO COMPONENT				4.	CONNECTING EMITTER TO SOURCE		LIMITED WARRANTY
IR Sensor	IR Controlled Components					This Linear product is warranted against defects in material and workmanship for twenty
Window			Cabinet Door			four (24) months. This warranty extends only to wholesale customers who buy direct
						from Linear or through Linear’s normal distribution channels. Linear does not warrant
						this product to consumers. Consumers should inquire from their selling dealer as to
					Connect IR emitter to source	the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the
						part of Linear LLC for consequential damages arising out of or in connection with
					input wall plate IR OUT jack	use or performance of this product or other indirect damages with respect to loss
Emitter attached directly			Emitter attached to		or to the IR OUT jack provided	of property, revenue, or profit, or cost of removal, installation, or reinstallation. All
to IR sensor window		Shelves	front cabinet door directly		on other sources	implied warranties, including implied warranties for merchantability and implied warranties
			opposite IR sensor window			for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu
> Peel off the adhesive cover and affix the emitter to the center of the IR sensor						of all other warranties express or implied.
window on the controlled component's front panel						All products returned for warranty service require a Return Product Authorization Number
> In some cases, it may be difficult to find the location of the IR sensor on the						(RPA#). Contact Linear Technical Service at 1-800-421-1587 for an RPA# and other
component. Consult the owner's manual of the unit for the IR sensor location.						important details.
		Shelves			To IR emitter
					ENC-SIWP
	Sensor attached on shelf directly				Source Input
					Wall Plate	Copyright © 2009 Linear LLC				P691
	above or below IR sensor window