SECO-LARM USA SK-1011-SQ warranty Installer Programming, User Code Worksheet, Specifications

Digital Access Keypad Manual

INSTALLER PROGRAMMING

These functions should only be used by professional installers, as incorrect entries can disable the entire keypad function.

Enter Programming Mode							(DEFAULT: 0 0 0 0 )
Enter Master code				Confirm			Function
X X X X *				*			Enter into programming mode
*Key in the Master Code.
Note: For first-time use, Master code is						0 0	0 0
Data Refresh
Option			Confirm	Function
8	9 0	1	#	Clears all previously stored data.
Configure Relay Outputs							(DEFAULT: Momentary, 1-sec. output)
Option		Output time		Confirm		Function
4	0	1 to 999		#		Relay momentary mode, from 1 to 999 seconds
4	1			#		Relay shunt mode (ON/OFF)
Relay Output Inhibit Control (lockout mode)							(DEFAULT: Momentary, 1-sec. output)
Option		Code Entry		Confirm		Function
5	0	1 to 999		#		Lockout for 1 to 999 seconds
5	1			#		Lockout shunt mode (ON/OFF)
Wrong Code Lockout							(DEFAULT: 10 tries / 30 seconds)
Option			# of tries	Confirm	Function
7	0				After 10 successive wrong codes, 30-second lockout
7	1				After 10 successive wrong codes, Duress activated
7	2		5 to 10	#	After 5 to 10 wrong codes, 15-min. lockout - Can reset with Master Code
7	6 0	0		#	None of the above
Output Activation Announcer							(DEFAULT: On)
Option		Code entry		Confirm	Function
		{	1	#	1-sec. beep notifies the user to open the door when the output relay is activated with the
8	1				user code or egress button. Use with a locking device which gives no sound when it
					activates, such as a magnetic lock.
			0	#	The beep is disabled, replaced by 2 short beeps for valid user codes.
User Code Entry Mode							(DEFAULT: Manual)
Option		Code entry		Confirm	Function
		{	1	#	Auto Entry Mode is selected. The # key that follows the user code is NOT required in
8	2				code entry. The User Codes MUST be set to the same digit length as the Master Code,
					from 4-8 digits.
			0	#	Manual Entry Mode is selected. The # key that follows the user code is required in
					code entry. The User Codes can be 4-8 digits, but not necessarily all of the same length.
Keypress Beeps							(DEFAULT: On)
Option		Code entry		Confirm	Function
8	3	{	1	#	Keypad beeps when a key is pressed.
			0		Silent operation -- keypad does not beep when a key is pressed.
				#

Exit Programming Mode

Confirm Function

*Exits programming mode, returns keypad to normal operations

USER CODE WORKSHEET

To print out a blank worksheet where all user codes can be recorded, please visit www.seco-larm.com and select the Model #, "SK-1011-SQ" in the drop down menu for the burglar section. On the product page click on "User Code Worksheet," which will load the .PDF.

Digital Access Keypad Manual

SPECIFICATIONS:

Power:

•Operation voltage -- 12-24 Volts AC/DC. No jumper needed to set voltage.

•Stand-by current drain -- 10mA @12VDC.

•Active current drain (press keypad key) -- Under 30mA.

•Active current drain (relay activated) -- Under 80mA.

Outputs:

•Relay output -- 5A @ 28VDC, Form "C", N.O./C./N.C., programmable for 1 to 999 second timed output or shunt (start/stop) output. Three terminals.

•Tamper output -- N.C. output. Connect to tamper circuit of alarm control panel. Two terminals.

Inputs:

•Power -- 12-24Volts AC/DC. Two terminals.

•Egress -- N.O., ground (-). Single terminal.

Code Operation:

•Up to 100 user codes, 10,000 possible user code combinations.

•Max. 10 seconds to enter each digit.

•Max. 30 seconds to enter each code.

Dimensions (keypad with back box):

•4-5/8" x 2-7/8" x 1-7/8" (117 x 74 x 48 mm).

Weight (keypad with back box):

•6.3 oz. (180 grams).

WIRING (SAMPLE INSTALLATION):

	Tamper	(+) (--)	OUTPUT 1					EG
	N.C.	12~24V AC/DC	N.C.			C. N.O.
Connect to the N.C.				(+)
24hr. zone of alarm
panel or other
signalling device.				N.C.			N.O.
					OR

+	--		Electric
12VDC		+	Lock	--
	power
	supply

	(for DC		REMARKS:
Diode			Output relay
	use only)		N.O. output for fail-secure lock.
1N4004			N.C. output for fail-safe lock.
Cathode				Additional egress buttons
Egress button (inside the
		N.O.	N.O.	can be connected in parallel
protected premises)				as needed

Page 6 SECO-LARM U.S.A., Inc. Page 3