Excalibur electronic AL-1000ATV2 Optional Pager Unit And Backup Battery, Programming Transmitters

transmitter activating the 3rd Channel Output, but only when the ignition is "on". The Anti-Carjacking feature automatically activates for each of the three described conditions, provided that each has been programmed to operate. In each of the three methods, the vehicle operator has 53 seconds to press the Valet Switch to cancel the Anti-Carjacking feature. If not cancelled, at 53 seconds the siren will start chirping, to remind the operator that Anti-Carjacking will engage. This will continue for 7 seconds, during which time the Anti-Carjacking feature may still be cancelled by pressing the Valet Switch. At 60 seconds, the Anti-Carjacking feature fully engages, sounding the siren and flashing the parking lights. Thirty seconds after the siren sounds and the parking lights flash, the starter interrupt will engage. During this 30 second period, if the ignition is turned "off" the starter interrupt will

instantly engage.

Once fully activated, the Anti-Carjacking feature can only be deactivated by turning the ignition "off", then "on" again, after which the Valet Switch must be pressed within 5 seconds. When the Anti-Carjacking feature is fully engaged, the system will not respond to the transmitters, nor will it automatically reset after 60 seconds. The Anti-Carjacking operation will continue until deactivated or until the vehicle's battery is drained.

Page - 24

the transmitter button which is desired to arm and disarm the system.

3)Repeat this procedure for each transmitter desired to operate the security system. The system will chirp the siren once to confirm that each transmitter code was learned. Both of the other two transmitter button's functions will automatically be learned when the arm / disarm button is learned. If a code is not received within a 10 second period, the learning process will automatically terminate.

Although this security system is programmed at the factory for the large center transmitter button to arm and disarm the system, any one of the transmitter's three buttons may be programmed to arm and disarm the security system. Upon the system learning the arm / disarm button, the other two buttons are automatically assigned other functions, as follows:

Arm / Disarm	Trunk Release	3rd Channel
Large Center Button	Small Right Button	Small Left Button
Small Right Button	Large Center Button	Small Left Button
Small Left Button	Large Center Button	Small Right Button

Optional Pager Unit And Backup Battery

This security system is designed for easy compatibility with the Omega Pager unit and also for a Backup Battery (both of which are optional additional compo- nents). The Omega Pager will alert the user to a security system violation, and also indicate which protected zone caused the violation. The Backup Battery option will allow the security system to operate even if power is removed from the system's control module or if the vehicle's battery is disconnected. The Omega dealer from which you purchased your vehicle security system can provide more details on the exact operations of each of these options.

Programming Transmitters

When adding or deleting transmitter codes to operate the security system, follow this process:

1)Turn "on" the ignition.

2)Within 5 seconds of turning "on" the ignition, press the Valet Switch 5 times. The siren will chirp, confirming that for the next 10 seconds the system is ready to learn a transmitter code. When the first transmitter code is learned all existing

stored codes will be erased. To enter a transmitter code, simply press and release

Page - 25

Programming Features

Your vehicle security system has 22 programmable features that allow your system to be customized to fit your personal needs. To program these features "on" or "off", follow this process:

1)Turn "off" the ignition.

2)Within 5 seconds of turning "off" the ignition, press the Valet Switch 5 times. The siren will chirp, followed by a short siren burst, confirming that for the next 10 seconds the system is ready to receive a feature number.

3)Press the Valet Switch the number of times that is equal to the feature number. Example: Press the Valet Switch six times if Feature #6 is to be changed.

4)The siren will respond by chirping the same amount as the feature number. Example: The siren responds with six chirps.

5)Press the large transmitter button to turn the feature "on". When done, the siren will respond with one chirp.

Page - 26 Page - 27