Important
Bienvenue dans la gamme de produits
First Alert® En plus de la tranquillité d’esprit votre coffre numérique First Alert® vous permettra de conserver vos objets de valeur en toute sécurité pendant bon nombre d’années.
Pour une sécurité maximum, vous devriez:
Régler immédiatement votre propre code personnel.
Ranger les clés et votre code personnel en dehors du coffre.
Le code par défaut de votre coffre est:
3*
Vue d’ensemble
2 | 3 | 4 | 5 |
1
1 | 2 |
|
4 | 5 | * |
|
|
6 | 8 | 9 | 10 |
1.Symbole de la fermeture par la clé de sécurité
2.Verrou à clé prioritaire
3.Bouton rotatif ou poussoir d’ouverture du verrou
4.Symbole du verrou ouvert
5.Voyant lumineux
6.Couvercle du coffre
7.Bouton de réglage du code rouge (voir schéma sur la droite)
8.Symbole de la clé de sécurité non fermée
9.Symbole du verrou fermé
10.Touches du pavé numérique
11.Prise du trou de fixation du câble de sécurité
+ | + |
| 7 |
11 |
Votre boîte de sécurité comprend
•(4) batteries "AA”
•(1) Éponge en mousse permettant d’assurer une protection ajoutée à vos objets de valeurs
•(2) Clés de priorité
•(1) Couvercle de la serrure de sécurité
•(1) Câble sécurisé en acier de 4 pieds
(3040DF, 3040DEF)
• (1) Fixation du câble de sécurité Prise du trou
(3040DF, 3040DEF)
Français
Getting Started
STEP 1: Locate Override Keys
Keys and batteries are stored in the packing material. Remove them before discarding the box.
STEP 2: Opening your Security Box using your Override Key
Remove cover from key lock.
Insert Override Key into key lock and turn the key counter clockwise one quarter turn to the unlocked position.
Turn the knob
To open, lift from the outer edge of the lid. (fig.2)
STEP 3: Installing Batteries
Locate the battery cover on the back side of the lid. (fig.4)
Slide the cover off the battery compartment.
Properly insert batteries, noting correct direction, replace cover and close the Security Box lid.
Return the Override Key and the knob to the locked position.
NOTE: Clean the battery contacts in the battery compartment and on the batteries before installing new batteries
STEP 4: Opening your Security Box using the pre-set factory code
THE PRE-SET FACTORY CODE IS 3 *
Using the keypad, enter the factory 
button is pressed. You will hear the Security Box unlock.
NOTE: You have 10 seconds to open the Security Box. If the green light goes out, you will have to
To open, turn the knob from the locked position to the unlocked position, one quarter turn
If the LED light flashes red after you enter the code, this means the code was entered incorrectly and the Security Box will not open.
NOTE: If an incorrect code is entered 3 times in a row, the Security Box will automatically shut down for 4 minutes before it can be opened again using the correct code. During this delay, the Override Key can be used to open the Security Box.
10
Programming your
Personal Passcode
NOTE: For your security, immediately
Open your Security Box with the Override Key or with the
On the inside of the lid, find and press the red button located to the side of the battery compartment (Fig.3). The LED light above the keypad will flash orange.
Enter your personal Passcode, up to 5 digits, followed by the 
button and then repeat a second time. You must enter the number twice.
For example: 1 2 3 4 5 
- 1 2 3 4 5 
After the first entry, the LED will flash orange. After the second entry, the LED will flash green and then go out.
Your Personal Passcode is now saved. Write it down and store it in a secure place away from the Security Box.
Close the lid of your Security Box and return the knob to the locked position (Fig. 6). If the override key was used, turn to the locked position, remove and replace the lock cover.
NOTE: The factory
| English | 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|