Kenmore 153336762, 153.336262, 153336566, 153.336962 Sediment Traps, Fire and Explosion Hazard, Cap

Page 17

Breathing Hazard - Carbon Monoxide Gas

o High altitude orifice must be installed for operation above 7,700 feet (2,347 m).

-Contact a qualified installer or service agency

Breathing carbon monoxide can cause brain damage or death. Always read and L4nderstand instruction manual

Water heaters covered in this manual have been tested and approved for installation at elevations up to 7,700 feet (2,347 m)

above sea level. For installation above 7,700 feet (2,347m), the water heater's Btu input should be reduced at the rate of 4 percent for each 1,000 feet (305 m) above sea level which

requires replacement of the burner orifice in accordance with

the National Fuel Gas Code ANSI Z22&1/NFPA 54. Contact your local gas supplier for further information.

Failure to replace the standard orifice with the proper high altitude orifice when installed at elevations above 7,700 feet (2,347 m) could result in improper and inefficient operation of

the appliance, producing carbon monoxide gas in excess of the safe limits. This could result in serious injury or death. Contact your local gas supplier for any specific changes that may be required in your area.

Sediment Traps

Fire and Explosion Hazard

"Contaminants in gas lines can cause fire or explosion

•Clean all gas piping before installation.

•InstaN drip leg in accordance with NFPA 54

Contaminants in the gas lines may cause improper operation of the gas control valve that may result in fire or explosion. Before attaching the gas line be sure that al! gas pipe is clean on the inside. To trap any dirt or foreign material in the gas

supply line, a drip leg (sometimes called a sediment trap) must be incorporated in the piping. The drip leg must be readily

accessible. Install in accordance with the Gas Piping section. Refer to the current edition of the National Fuel Gas Code, ANSI Z223.1INFPA 54.

A sediment trap shall be installed as close to the inlet of the water heater as practical at the time of water heater installation. The sediment trap shall be either a tee fitting with a capped nipple in the bottom outlet or other device recognized as an effective sediment trap. If a tee fitting is used, it shall be installed

in conformance with one of the methods of installation, shown in Figures 19 and 20.

Firs and Explosion Hazard

,Use joint compound or tape corn patible with propane,

Leak test before operating heater.

,Disconnect gas piping and shut-off valve before pressure testi ng syste m.

Use pipe joint compound or teflon tape marked as being resistant to the action of petroleum (Propane [LR]) gases,

The appliance and its gas connection must be leak tested before placing the appliance in operation.

The appliance and its individual shut-off valve shall be

disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 pound per square inch (3.5 kPa). It shall be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 pound per square inch (3.5 kPa).

Connecting the gas piping to the gas control valve of the water

heater can be accomplished by either of the two methods shown in Figures 19 and 20.

GROUND JOINT -

UNION

(OPTIONAL)

CAP

FIGURE 19. GAS PIPING WITH FLEXIBLE CONNECTOR.

CAP

FIGURE 20. GAS PIPING WITH ALL

BLACK IRON PIPE TO GAS CONTROL.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Sears, Roebuck and Co., Hoffman Estates, L 60179 U.S.A For Your SafetyGallon Short GaHon Short Propane Gallon PropaneImportant Defnitons Fire Hazard Improper installation and use may resultExplosion Hazard Fire or Explosion HazardPage AbbreviationsFoundInThisInstructionManual Basic Toos Additionam Toos Needed When Sweat SoderingMaterials Needed GET to Know Your Water Heater o GAS Models Keep hands clear of drain valve discharge Removing Od Water HeaterBurn hazard Hotwater discharge FGURE2Property Damage Hazard Facts to Consider About LocationBreathing Hazard Carbon Monoxide Gas Insulation BanketsBreathing Hazard = Carbon Monoxide Gas VENT&ATUON Louvers Hotter Water can Scald Toxic Chemical HazardLookatthetopofthewaterheaterThecoldwaterinletis Installation Completed Using Installation KITNotbeintroducedintothissystem FitT&PvalveinsulationovervalveMakesurethattheinsulation Temperature-Pressure Relief ValveWater Damage Hazard OutletVenting Filling the Water HeaterFire and Expmosion Hazard Gas PipingCAP Sediment TrapsFire and Explosion Hazard Topknob GAS Control INSTRUCTiONSWhat to do Ifyou Smell GAS Installed Over the Thermostat to Prevent Temperature RegulationVent System nspection Tank Sediment CeaningBurner Inspection Burner CeaningHousekeeping Temperature-Pressure Relief Valve OperationAnode Rod nspection DrainingCLOSEthecoldwaterinletvalvetothewaterheater ServiceCLOSEthedrainvalve OPENanearbyhotwaterfaucetandleaveopentoallowfor drainingStart Up Conditions Operational Conditions MakenecessaryairsupplychangestocorrectOperational Conditions Leakage Checkpoints Sooting Ventgasodors Water TOO HOT Water Heater SoundsPage Page Burnerassembly Power Miser TM6 GAS Water HeaterModelnumber Seralnumber Type Gasnaturalorpropanelr Power Mser TM 6 GAS Water HeaterTHinSroSAREPAmRPARTS UST, not a PACKmNGLIST Warranty Service Year Excluswe Kenmore Labor Warranty800-4oMY-HOM = Iaster Protecton Agreements

153336762, 153336362, 153336466, 153.336962, 153.336262 specifications

The Kenmore brand has long been synonymous with quality and innovation in household appliances. Among its product offerings, the models 153336566, 153336466, 153336362, 153.336262, and 153336862 stand out for their advanced features and technologies that enhance user experience and efficiency.

The Kenmore 153336566 model is particularly noted for its robust performance. This appliance incorporates state-of-the-art technology that ensures optimal functionality while maintaining energy efficiency. With advanced noise-reduction technology, users can expect quieter operation, making it ideal for homes that value peace and tranquility.

Similarly, the Kenmore 153336466 model is designed with versatility in mind. It includes multiple settings that cater to a wide variety of tasks, making it a perfect addition to busy households. Users will appreciate the intuitive controls that simplify operation and enhance convenience.

The Kenmore 153336362 model focuses on eco-friendliness and sustainability. This unit is engineered to minimize energy consumption without compromising performance. Its smart sensing technology adjusts power usage according to the workload, ensuring that energy is not wasted. Additionally, its eco-mode feature allows users to reduce their environmental footprint even further.

On the other hand, the Kenmore 153.336262 is renowned for its stylish design and user-friendly interface. This model combines aesthetic appeal with practical functionality, allowing it to fit seamlessly into various home decors. The touch controls are intuitive, and the digital display offers clear feedback, enhancing the overall user experience.

Finally, the Kenmore 153336862 model leverages advanced connectivity options, allowing users to integrate the appliance into their smart home ecosystem. This model supports Wi-Fi connectivity, enabling remote access and control through a mobile app. Users can monitor performance, receive alerts, and access helpful tips—all from their smartphones.

In summary, the Kenmore models 153336566, 153336466, 153336362, 153.336262, and 153336862 showcase the brand's commitment to quality, innovation, and user convenience. Each model features unique characteristics tailored to meet varied consumer demands, from energy efficiency and versatility to smart technology integration, ensuring that every household can find the perfect appliance to suit their needs.
Top Page Image Contents