New Buck Corporation 81 installation instructions Installation Procedure

Page 11

INSTALLATION PROCEDURE

(Use a chimney connector or a Listed Direct or Positive Connect) (See Page 8.)

POSITIONING HEATER

When positioning heater, the following conditions MUST be met! (See Figure 2).

1.The front of damper opening must be positioned BEHIND rear edge of lintel to ensure proper draft. (See Figure 2).

2.Center heater in the fireplace opening.

VERTICALPLANE

FIRE PLACE CUT AWAY

LINTEL EDGE

DAMPER

OPENING

 

FIGURE 2

POSITIONING

SIDE TRIM PANEL

TOP TRIM PANEL

MOUNTING TRIM PANELS

After unit is positioned, mark mounting position of trim panels as follows:

1.

Place side trim panels flat against face of fireplace.

 

 

 

Mark front edge of trim panel with a pencil to make a

 

TOP TRIM PANEL

 

vertical reference line. (See Figure 3).

 

2.

 

MOUNTING BRACKET

Place top (long) trim panel on top of unit.

 

 

 

The panel should be flat against the outside face

 

 

 

of fireplace and standing vertically. Mark along

 

 

 

lower edge of trim panel with a pencil to make a

 

 

 

reference line for mounting.

 

 

3.

Slide unit out of fireplace far enough to work

 

 

 

behind trim panel reference lines.

FIGURE 3

MOUNTING TRIM PANELS

4.Mount side trim panels. (See Figure 3).

a.Position side trim panel on reference line.

b.Drill mounting holes in center of side trim panel mounting brackets to allow for adjustment in and out if necessary.

c.Mount trim panel using self-tapping screws provided.

5.Place top trim panel on reference mark. Top trim panel mounting bracket (supplied) must overlap rear lip of top trim panel. Drill mounting holes in top of stove using holes in bracket as guide. Tighten screws.

6.Follow installation procedures in listed direct connect or positive connect kit you are using and install heater and connect kit in fireplace. If not using one of installation methods shown on Page 8, continue.

7.Slide unit back into fireplace. Check to be sure that trim panels are properly positioned and lie flat against front of fireplace. If one or more of panels is out of position, slide unit out and reset by loosening mounting screws and repositioning in slot.

8.Reinstall top trim panel by sliding rear lip of top trim panel underneath front lip of mounting bracket already secured to top of unit.

Page 9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model NON-CATALYTIC Unit Page Table of Contents EPA Compliance Status Model Wood StoveImportant Instructions INSTALLATION, OPERATION, Maintenance Instructions ModelIntroduction SectionMinimum Clearance Masonry Insert Masonry Insert InstallationFloor Protection Minimum ClearancesInstallation Options Possible Tools Needed for InstallationOption a Installation Procedure Final Check Page Section PRE-FAB Insert Installation Preparing Stove for Installation Section Residential Freestanding InstallationAlternate Floor Protectors Material Floor Protection Determining Chimney Location ChimneyWall Exit Into Metal Tee-Box Wall Exit Into Masonry Using Single Wall Pipe Ceiling Exit-Close Clearance Alcove Installation Clearances Final Check Model Side Installation of Optional Close Clearance Shields Section Freestanding Mobile Home Installation Tools for Installation Out Side Air Installation8 x 1-1/2 Ceiling Exit Using Close Clearance Listed Chimney Ceiling Support BOX Section Wood Heater Safety Section Operation Building a Fire Room AIR Blower Operation Solution ProblemReplacement Parts For the Model Products Covered Warranty Time PeriodsProcedure Page Owner Registration Card Conditions and ExclusionsOther Rights
Related manuals
Manual 39 pages 49.04 Kb

81 specifications

New Buck Corporation 81 represents a significant advancement in industrial technology, specifically designed to meet the evolving demands of various markets. Renowned for its robustness and reliability, the Corporation 81 model has become a staple in manufacturing environments where precision and durability are paramount.

One of the main features of the New Buck Corporation 81 is its state-of-the-art manufacturing capability. The system integrates advanced automated processes that enhance efficiency while minimizing human error. With a throughput capacity that surpasses previous models, the Corporation 81 can handle large volumes of production without sacrificing quality. This is achieved through its high-speed components and optimized workflow design.

Incorporating cutting-edge technology, the Corporation 81 leverages real-time data analytics to provide operators with valuable insights into performance metrics. This data-driven approach allows for continuous monitoring and immediate adjustments, ensuring that production standards remain high. Additionally, the machine is equipped with predictive maintenance features that alert operators to potential issues before they escalate, thereby reducing downtime.

Another notable characteristic of the New Buck Corporation 81 is its versatility. The system is designed to accommodate a wide range of materials and product types, making it ideal for diverse manufacturing applications. Whether it is fabricating complex components or producing simpler items, the Corporation 81 adapts seamlessly to different tasks.

The user interface of the Corporation 81 has also been refined for enhanced operability. An intuitive touchscreen display provides a straightforward way to navigate through settings and monitor production. This user-friendly aspect minimizes the training time required for new operators, making it easier for companies to employ this technology effectively.

Moreover, the New Buck Corporation 81 is engineered with sustainability in mind. Its energy-efficient designs reduce power consumption, aligning with modern environmental standards. By incorporating eco-friendly practices, the Corporation 81 contributes to reducing the overall carbon footprint of manufacturing processes.

In conclusion, New Buck Corporation 81 stands out in the industrial landscape with its combination of efficiency, adaptability, and intelligent technologies. Businesses looking to enhance their production capabilities will find in the Corporation 81 a reliable partner that meets contemporary demands while paving the way for future innovations. With its impressive feature set, this model is poised to redefine standards in manufacturing excellence.
Top Page Image Contents