Heat & Glo LifeStyle 50 Seasoned Wood, Starting a Fire, Grate, Firescreen, Flue Damper

Page 7

B. Seasoned Wood

Properly seasoned wood is important for successful opera- tion of your fireplace. Most woodburning fireplace problems are caused by burning wet, unseasoned wood.

Seasoned firewood is wood that is cut to size, split and air dried to a moisture content of around 20%.

Imagine a wooden bucket that weighs about eight pounds. Fill it with a gallon of water, put it in the fireplace and try to burn it. This sounds ridiculous but that is exactly what you are doing if you burn unseasoned wood.

A tree cut down a year ago and not split is likely to have almost as high a moisture content now as it did when it was cut.

Please refer to Section 2.M. for more detail.

C. Starting a Fire

NOTICE: You must establish a good draft to prevent smoke spillage into the room.

WARNING! Risk of Fire! Keep combustible materials, gasoline and other flammable vapors and liquids clear of the fireplace.

DO NOT:

store flammable materials close to the fireplace

use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace.

Keep all flammable liquids well away from the fireplace while it is in use. Combustible materials may ignite.

The first three or four fires should be of moderate size to allow the oils and binders to be burned from the fireplace and the molded brick panel, and paint to cure. You may notice an industrial odor the first few fires. This is considered normal.

Use well-seasoned wood (see Section 2.M.).

Open the flue damper to a fully open position.

Place crumpled or twisted paper under the fireplace grate.

Loosely arrange kindling or small pieces of wood to form a ‘tent’ on the fireplace grate.

Pre-warm the flue to establish a draft to help reduce smoke spillage during start-up. Hold a rolled up piece of burning newspaper under the flue damper for a few moments.

Light the crumpled paper to ignite the kindling.

Add small pieces of wood until a hot bed of embers has been established.

Add a minimum of three average size pieces of split firewood, placed to allow combustion air and flames between them.

CAUTION! Odors and vapors released during initial opera- tion may be irritating to sensitive individuals. Open windows for air circulation.

D. Grate

This fireplace is designed to be used with the grate sup- plied with this unit or one approved by HHT. The grate will deteriorate over time and will need occasional replacement.

WARNING! Risk of Fire! Use only the factory-supplied integral grate.

Keeps logs in place.

Allows proper air circulation around the fire.

E. Firescreen

The firescreen is provided to control sparks. Keep it closed when the fireplace is in use.

WARNING! Risk of Fire or Burns!

Screen will not prevent burning materials from falling out.

Screen pulls or handles may be hot.

F. Flue Damper

Refer to Figure 2.1 for location of control.

Must be in fully open position (handle up toward the top of the fireplace) during operation of the fireplace.

Before lighting the fireplace, verify fully open position by looking up from the inside of the fireplace.

WARNING! Risk of Fire and Asphyxiation! Open damper prior to operating fireplace. A closed damper overfires the fireplace and will cause smoke and flames to spill into the room.

G. Outside Air

Refer to Figure 2.1 for location of controls.

Outside air doors should be in the fully opened position during operation of the fireplace.

Before lighting the fireplace, turn both handles & pull out to open. Reverse steps to close and lock.

H.Molded Brick Panel

The molded brick panel is shipped separately, but required to contain heat and provide an attractive interior.

It will deteriorate over time and will need occasional replacement. Small hairline cracks and discoloration are normal and do not affect its safety.

Cracks in the mortar may occur and do not affect the safety of the unit. If mortar falls out of the joints and metal is exposed, replace or patch the mortar.

(See Molded Brick Panel Maintenance, Section 3.C.)

WARNING! Risk of Fire! DO NOT burn fireplace without molded brick panel. Use only molded brick panel supplied by Hearth & Home Technologies, Inc.

Heat & Glo • RUTHERFORD-504059-333 Rev C • 06/08

7

Image 7
Contents RUTHERFORD-50 Listing Label Information/Location Homeowner Reference InformationUser Guide Table of ContentsInstaller Guide Safety Alert KeyWarranty For Heat & GLO Fireplaces Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsYour Fireplace Operating InstructionsFirescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelChimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Check Firebox Molded Brick Panel Glass CleaningInspect Grate Start Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDraft Design and Installation ConsiderationsNegative Pressure Recommended Chimney Locations Locating your Fireplace & ChimneyTypical Fireplace Components Tools and Supplies NeededInspect Fireplace and Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Outside Air Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsCut Roof Opening Installation NotesInstall Firestop Frame OpeningsSupplementary Support and Stabilizer Assemble Chimney SectionsInstall Roof Radiation Shields Install Attic Insulation ShieldFinish Top Offset Elbow InstallationEnclosures Slanted Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Flashing Install Fireplace & ChimneyInstall Termination Cap Shroud Requirements ShroudsHouse Style Shroud House Style Shroud Minimum DimensionsPyramid Style Shroud Arch / Mailbox Style ShroudInstall Back Molded Brick Panel-Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Side Molded Brick Panel-TraditionalInstall Back Molded Brick Panel-Herring- bone Install Side Molded Brick Panel-Herring- boneInstall Screens Install MortarHearth Extension Finishing= 1/k x inches of thickness Raised Hearth Extension Framing Non-combustible Sealant Noncombustible Facing Finishing MaterialStandoffs Combustible MantelBrick Front Gas Log/Lighter Provision AccessoriesWood Burning Inserts Reference Materials Fireplace DimensionsRequired/shipped separately Fireplace ComponentsCatalog # Description Chimney Components¨ C. Service Parts At Depot StockedThis page intentionally left blank This page intentionally left blank Do not Discard this Manual

50 specifications

The Heat & Glo LifeStyle 50 is a contemporary gas fireplace that embodies a perfect blend of modern aesthetics and cutting-edge technology. Designed for those who seek elegance and functionality, this fireplace is ideal for both new constructions and renovations, making it a versatile choice for any home.

One of the standout features of the LifeStyle 50 is its large viewing area. With its expansive glass front, it presents a stunning display of flames that creates a warm and inviting atmosphere. This design not only maximizes the visual impact but also enhances the overall ambiance of the living space. The fireplace allows for customizable flame and ember bed colors, enabling homeowners to personalize their experience further.

The LifeStyle 50 incorporates advanced heating technology that ensures efficient warmth distribution. With a powerful heat output, this model can effectively warm larger areas, making it suitable for open-plan living spaces. The fireplace operates quietly and efficiently, utilizing a user-friendly remote control for convenient operation. This allows for seamless adjustments to temperature and flame settings at the touch of a button.

Moreover, the LifeStyle 50 is designed with ease of installation in mind. Its flexible venting options allow for both horizontal and vertical installation, accommodating various architectural layouts. The fireplace can be vented directly through the wall or roof, providing installers with greater versatility. The unit is also constructed using durable materials, ensuring longevity and minimal maintenance.

A key characteristic of the Heat & Glo LifeStyle 50 is its commitment to safety. Equipped with advanced safety features, including an automatic shut-off system and a glass front that remains cool to the touch, this fireplace prioritizes peace of mind for homeowners.

Additionally, the LifeStyle 50 is compatible with smart home integration, allowing users to control their fireplace through popular smart home systems. This connectivity enhances user experience, offering convenience and ease of access from anywhere.

In summary, the Heat & Glo LifeStyle 50 is a sophisticated gas fireplace that combines stylish design with smart technology, high efficiency, and safety features. Its adaptability, performance, and aesthetic appeal make it an excellent choice for anyone looking to add a touch of luxury and warmth to their home.