Firestop Spacers V3600FS-8DM, Penetrating roof

Venting Installation

Continued

Firestop Spacers (V3600FS-8DM)

Firestop spacers are required at each point where chimney penetrates a floor space. Their purpose is to establish and maintain required clearance between chimney and combustible materials. When pipe passes through a framed opening into a living space above, firestop must be placed onto ceiling from below as shown in Figure 12.

They also provide complete separation from one floor space to another or attic space as required by most codes. When double wall

4.Remove shingles around opening mea- sured. Cut out this section.

5.Add next sections of pipe until end penetrates roof line. Check to see that proper clearances are maintained. Extend chimney by adding sections of double wall pipe until pipe is minimum of 30" above highest point of roof cutout. Termination and chimney must extend a minimum of 36" above highest point where it passes through roof.

pipe passes through a framed opening into an attic space, firestop must be placed into an attic floor as shown in Figure 13.

If area above is a living space, install

firestop below framed hole.

Minimum Measurements

143/8"

(36.5 cm)	1"
	1"
	(2.5
	cm)

1" (2.5 cm)

30"

(76.2 cm)

(2.5 cm)

Figure 12 - Firestop Spacer with Living

Space Above Ceiling

Opening "A"

If area above is an attic or insulated area,

install firestop above framed hole.

Figure 13 - Firestop Spacer with Attic

Space Above Ceiling

Penetrating roof

To maintain a 2" clearance to pipe on a roof with a pitch, a rectangular opening must be cut.

1.Determine center point where pipe will penetrate the roof.

2.Determine center point of the roof. Pitch is the distance the roof drops over a given span, usually 12". A 6/12 pitch means that the roof drops 6" for each 12" measure horizontally down from roof rafters.

3.Use roof opening chart (Figure 14) to determine correct opening length and flashing required.

Pitch	Slope	Opening	Used Flashing
		"A" Max.	Model No.
Flat	0°	15"	V6F-8DM
0-6/12	26.6°	16 1/8"	V6F-8DM
6/12- 12/12	45.0°	20 3/8"	V12F-8DM

Figure 14 - Roof Opening Measurements

Flashing installation (v6f- 8dm or v12f-8dm)

Determine flashing to be used with roof open- ing chart. Slide flashing over pipe until base is flat against roof. Replace as many shingles as needed to cover exposed area and flashing base. Secure in position by nailing through shingles (see Figure 15, page 11). DO NOT NAIL THROUGH FLASHING CONE.

Installing Flashing on a Metal Roof When installing flashing on a metal roof, it is required that putty tape be used between flashing and roof. Flashing must be secured to roof using #8 x 3/4" screws and then sealed with roof coating to prevent leakage through screw holes. A roof coating must also be ap- plied around perimeter of flashing to provide a proper seal.

www.desatech.com

109034-01G

CWB36C, (V)B36LI, (V)B36I, (V)B36L, (V)B36 specifications

The Desa (V)B36LI, (V)B36I, CWB36C, (V)B36, and (V)B36L are notable products in the realm of gas log fires, designed to provide warmth while emphasizing efficiency and aesthetic appeal. These models integrate advanced technologies and features that distinguish them in the market.

One of the hallmark characteristics of these units is their versatility. They come in various configurations to suit different living spaces and personal preferences. The (V)B36LI and (V)B36I models are particularly known for their linear design, allowing for installation in modern homes where style and sophistication are priorities. The sleek design not only enhances interior aesthetics but maximizes the viewing area of the flames, providing a captivating focal point in any room.

When it comes to efficiency, these models are engineered with energy-saving technologies, ensuring optimal heat output with minimal gas consumption. The use of advanced burner systems ensures that heat is distributed evenly throughout the space, enhancing overall comfort. Some models are equipped with electronic ignition systems that provide reliable start-ups without the need for cumbersome matches or lighters.

The inclusion of programmable thermostats in some versions allows users to set and maintain their desired temperature with ease, promoting both convenience and energy efficiency. Many of these models also feature an environmentally friendly design, with reduced emissions compared to traditional wood-burning stoves, thus contributing to a cleaner environment.

User control is further enhanced through optional remote controls, giving homeowners the ability to adjust settings from the comfort of their seating area. The glass viewing windows are designed to be easily cleaned, ensuring that the elegance of the flames is always on display.

Materials used in the construction of the (V)B36LI, (V)B36I, CWB36C, (V)B36, and (V)B36L are selected for durability and heat resistance, ensuring that these gas fireplaces not only look impressive but also stand the test of time. With safety features such as protective screens and automatic shut-off systems, these models provide peace of mind alongside their heating capabilities.

In summary, the Desa (V)B36 series models are characterized by their stylish designs, energy efficiency, advanced technologies, and user-friendly features, making them an excellent choice for anyone looking to enhance their living space with a modern heating solution. Whether opted for ambiance, warmth, or efficiency, these gas log fires remain a top choice among consumers.