Desa T32N, T36N, T32P, T36P Venting Installation Instructions, Installation Precautions

Page 7

VENTING INSTALLATION INSTRUCTIONS

Installation Precautions

Installation Planning

7

VENTING INSTALLATION INSTRUCTIONS

NOTICE: Read these instructions completely be- fore attempting installation.

These models are tested and approved for use with DESA Interna- tional (direct-vent) pipe components and terminations.

The venting system must terminate on the outside of the structure and can not be attached to a chimney or flue system serving a separate solid fuel or gas burning appliance. A direct-vent appliance must have its own venting system. DO NOT common vent this appliance.

These models are approved to be vented either horizontally through an outside wall or vertically through a roof or chase enclosure using the following guidelines:

When venting system terminates horizontally on an outside wall, you must install a standoff if the termination cap is to be in- stalled directly on a combustible finish such as vinyl, wood, stucco, etc.

Never run the vent downward as this may cause excessive tem- peratures which could cause a fire.

Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal sections, which requires 2" clearance from the top of the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.

Snorkel terminations are required when minimum clearance to grade cannot be met (see Figure 16 on page 11).

Have fireplace and selected vent components on hand to help determine the exact measurements when elbowing or offsetting. Always use wall firestops when penetrating walls and firestops when penetrating ceilings or attic spaces.

Install horizontal venting with a 1/4" rise for every 12" of run toward the termination.

WARNING: Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious injury, property damage or loss of life.

NOTICE: Failure to follow these instructions will void the warranty.

INSTALLATION PRECAUTIONS

Wear gloves and safety glasses for protection

Use extreme caution when using ladders or when on roof tops

Be aware of electrical wiring locations in walls and ceilings

The following actions will void the warranty on your venting system:

Installation of any damaged venting component

Unauthorized modification of the venting system (Do not cut or alter vent components)

Installation of any component part not manufactured or ap- proved by DESA International

Installation other than as instructed by these instructions

WARNING: This gas fireplace and vent assembly must be vented directly to the outside. The venting system must NEVER be attached to a chimney serv- ing a separate solid fuel burning appliance. Each direct-vent gas appliance must use a separate vent system. Do not use common vent systems.

WARNING: Vent pipe air space clearances to com- bustibles are 1" on all sides except on the horizontal sections, which require 2" clearances from the top of the pipe. Where the termination cap penetrates a com- bustible wall, 1" air space clearance is required.

INSTALLATION PLANNING

There are two basic types of direct-vent installation:

Horizontal Termination

Vertical Termination

Horizontal Termination Installation

IMPORTANT: Horizontal square terminations require only inner portion of wall firestop. Horizontal installations using round termi- nation require exterior portion of wall firestop available only in vent kit HTK (see Figure 14, page 10).

1.Set the fireplace in its desired location and determine the route your horizontal venting will take. Do not secure the fireplace until all venting has been installed. Some installations require sliding the fireplace in and out of position to make final vent- ing connections. Figures 14 through 18 on pages 10 through 12 show different configurations for venting with horizontal termination that will help you decide which application best suits your installation. Check to see if wall studs or roof rafters are in the path of your desired venting route. If they are, you may want to adjust the location of the fireplace.

For morevisit www..com

108661

Image 7
Contents For Your Safety What to do if YOU Smell GAS For Your SafetySafety Information Table of ContentsLocal Codes Safety Information Product IdentificationPRE-INSTALLATION Preparation Product FeaturesLocation and Space Requirements Framing and Finishing ClearancesBalcony with Perpendicular Side Wall Location of Termination CAPHorizontal Termination Installation Venting Installation InstructionsInstallation Precautions Installation PlanningVent Pipe Connections Installing Horizontal Vent Cap T32 Series 31 min Horizontal Termination ConfigurationsSquare Termination VerticalCorner and Alternate Installation Venting with Two 90 Elbows Horizontal System Installation Using TWO 90 ElbowsFlat Ceiling Installation Installation for Vertical TerminationVenting with One 90 Elbow Vertical Termination ConfigurationsVertical Venting High Altitude InstallationCheck GAS Type Fireplace InstallationParts Lists for Venting Kits and Components Installing Optional Blower AccessoriesBlower Model BK Model BKT InstallationBlower Model BKT Blower Wiring DiagramInstallation Items Needed Installing GAS Piping to Fireplace LocationChecking GAS Connections Connecting Fireplace to GAS SupplyInstallation Items Needed Pressure Testing Gas Supply Piping SystemInstalling Remote Receiver Pressure Testing Fireplace Gas ConnectionsRemoving Glass Door Cleaning Glass DoorREMOVING/REPLACING Glass Door Removing Louver PanelsInstalling Log No Installing LOGS, Lava Rock and Glowing EmbersInstalling Logs No and No Lighting Instructions For Your Safety Read Before LightingManual Lighting Procedure Operating FireplaceTions on Optional Remote OperationGhrc Series Operation Ghrcta Series OperationOperating Optional GWMT1 Wall Mounted Thermostat Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersLogs Cleaning MaintenanceGlass Door Pilot and BurnersObserved Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Above Gas leak. See Warning statementParts Under Warranty Replacement Parts Service HintsSpecifications Technical ServiceAccessories VT32NRB Illustrated Parts BreakdownVT32PRB KEY Part Number Description QTY Parts ListVT36PRB For more Visit www Com Warranty Information

T32N, T36N, T32P, T36P specifications

Desa T32N, T36N, T32P, and T36P are prominent technologies that represent the cutting-edge advancements in the field of telecommunications and data transmission. These systems are crucial for a variety of applications, including telecommunications networks, data centers, and various other technological infrastructures that require high-speed and reliable data transfer capabilities.

Starting with the T32N and T36N models, these systems are characterized by their exceptional bandwidth capacity and high processing speeds. They are designed to cater to the growing demand for faster internet connections and efficient data handling. One of the main features of these models is their ability to support multiple channels simultaneously, allowing for numerous data streams to be processed at once. This is particularly beneficial for environments where data traffic is high, such as urban areas and corporate networks. The T32N and T36N utilize advanced modulation techniques to enhance signal quality, effectively minimizing interference and increasing overall throughput.

On the other hand, the T32P and T36P models are specially engineered for optimal performance under varying network conditions. These models are equipped with adaptive technologies that automatically adjust to network demands, ensuring consistent data delivery even during peak usage periods. The main trait of these systems is their resilience; they are built to withstand fluctuations in data traffic and environmental factors, making them suitable for deployment in diverse settings, from rural areas to densely populated cities.

All four models leverage state-of-the-art technologies such as MIMO (Multiple Input Multiple Output) and beamforming to maximize efficiency and coverage. MIMO technology allows these systems to transmit and receive multiple data streams simultaneously, significantly boosting the data rate and overall system capacity. Beamforming enhances the directivity of the signal, focusing the transmission toward specific receivers, which not only improves signal strength but also reduces interference with other devices.

Another noteworthy characteristic of the Desa T32N, T36N, T32P, and T36P family is their compatibility with a wide range of existing technologies and infrastructures. This interoperability allows for seamless integration into current systems, facilitating upgrades without the need for complete overhauls. As the landscape of technology continues to evolve, these models stand out for their robust features and adaptive capabilities, solidifying their position as essential tools in the advancement of telecommunications and data transfer solutions.