Vermont Casting HEF22 Replacing the Light Bulbs, Maintenance of Motors, Cleaning

Page 7

Replacing the Light Bulbs

Depending on your model, the fireplace uses two (2) or three (3) clear 120 Volt, 60 Watt, E-12 socket base light bulbs (small base, chandelier candle type). The lights are located under the ember bed of the unit. For convenience, if one of the light bulbs burns out, it may be easier to replace all of the light bulbs at the same time.

Do not exceed 60 Watts per bulb. Use of higher rated bulbs may result in a fire, causing property damage, personal injury or loss of life.

1.Turn off power to the unit.

2.Let fireplace cool if it has been operating.

3.Remove fixed front panel, or open doors (depend- ing on model).

4.Locate two (2) screws that hold the refractory (brick patterned) bracket together with the ember bed. (Fig. 5) (Not applicable to HEF22)

5.Remove those two (2) screws using an appropriate screwdriver. One screw is located on either side of the unit.

 

Remove Screws

Fig. 5

Remove screws that hold refractory bracket with

6.Pull the ember bed out of the unit, by gently pulling towards you and only slightly upwards. Depending on the model, you can remove the refractory prior to removing the ember bed.

Pull Here (both sides)

Fig. 6 Pull ember bed out of unit.

7.Looking into the opening of the unit under the ember bed, visually locate the light bulbs.

8.Remove the light bulbs by unscrewing them out of the bases, turning them counterclockwise. You can use one hand to hold the light socket in place, if required.

9.Install the new light bulb(s) by turning the light bulb into the base clockwise. You can use one hand to hold the light socket in place, if required.

60 W Light Bulbs

Fig. 7 Remove and replace light bulb(s).

10.Reposition the ember bed. If required, gently raise the refractory panels, one at a time, to tuck the ember bed edge underneath them.

11.Reposition the refractory bracket, aligning the refractory in place as required.

12.Replace two (2) screws taken out in Step 5, by using an appropriate screwdriver.

Maintenance of Motors

The motors used on the fan and the drum assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacu- uming of the fan/heater is recommended.

Make sure the power is turned OFF before proceeding.

Cleaning

Cleaning of the touchpad label at the bottom front of the unit is to be done only using a soft cloth, slightly dampened in water (if needed, a small amount of dish soap can be added to the water) and dried using a clean, dry soft cloth. DO NOT use any abrasive house- hold cleaners as these products will damage the touchpad controls.

10006946

7

Image 7
Contents HEF26 HEF33 HEF36 Table of Contents Clearance to Combustibles Installation Instructions GeneralCabinet Installations Locating Your FireplaceElectrical Specifications Fireplace DimensionsElectrical Connection Direct Hard Wiring Electric FireplaceReplacing Front Cover Service InstructionsGlass Information Cleaning Maintenance of MotorsReplacing the Light Bulbs Electrical Wiring Diagram Flame Speed Control Operating InstructionsHeater Control HEF22/26/33/36 Electric Fireplace HEF22/26/33/36 Electric Fireplace Year Warranty

HEF22 specifications

The Vermont Casting HEF22 is a remarkable freestanding gas fireplace that combines modern technology with timeless charm to create an efficient and attractive source of heat for homes. This model is known for its exceptional craftsmanship, sturdy construction, and stylish design, making it a popular choice among homeowners looking to enhance their living spaces.

One of the standout features of the HEF22 is its high-efficiency rating. It is designed to maximize heat output while minimizing energy consumption, ensuring that rooms are warmed quickly without excessive gas use. This efficiency not only saves homeowners money on their energy bills but also contributes to a more environmentally-friendly heating solution.

The HEF22 incorporates advanced technologies that enhance its functionality and ease of use. Equipped with an electronic ignition system, it provides reliable start-up performance, eliminating the need for cumbersome match lighting. Additionally, the unit is designed with a built-in thermostat that allows for precise temperature control, ensuring optimal comfort at all times.

Another notable characteristic of the Vermont Casting HEF22 is its wide viewing area, which features a beautiful ceramic glass window. This allows for an unobstructed view of the realistic flame simulation, providing a warm and inviting ambiance to any space. The flames can be beautifully accented with decorative fire glass or ceramic logs, further elevating the visual appeal of the fireplace.

The design of the HEF22 is versatile, available in a variety of finishes and color options to complement any decor style. Its compact footprint makes it suitable for various room sizes, whether it's a cozy den, a spacious living room, or even an outdoor patio when appropriately adapted.

The Vermont Casting HEF22 also emphasizes safety features, including a safety shut-off system and a protective screen, ensuring peace of mind for homeowners. This model represents a perfect blend of innovation and tradition, making it an ideal choice for those seeking both aesthetic beauty and dependable heating performance.

In summary, the Vermont Casting HEF22 is a standout in the gas fireplace market, delivering high efficiency, advanced technology, and attractive design. Its features cater to both functionality and style, making it a top choice for modern homeowners. With its ability to create a warm, inviting atmosphere, the HEF22 is more than just a heating appliance; it is a statement piece that enhances any living environment.