Vermont Casting 7PDVS manual DV Power Vent System

Page 3

DV Power Vent System

General Information and Instructions for the DV-Power Vent System Model 7PDVS

•This DV Power Vent System was designed to be used only on units with electronic ignition (EN or EP).

•This DV Power Vent System was certified by CSA to be used only with CFM Corporation Direct Vent models, as listed in this manual.

•This DV Power Vent System can be used with any CFM Corporation side wall vent termination kits, vertical vent termination kits or snorkel kits (rear vent termination not to be used).

•This DV Power Vent System must be installed by a qualified professional according to these instructions.

•Plan the venting layout before starting the installa- tion.

•Maximum TOTAL allowable system length is 40FT of straight pipe, plus up to five 90 degree elbows. Any combination of 45 and 90 degree elbows up to a maximum of 450 degrees is allowed. It is NOT per- missible to substitute elbows for length of horizontal or vertical straight pipe.

•Can be vented down to a maximum of 12FT, meas- ured from the center line of the highest section to the centre line of the lowest section between the fireplace and the DV Power Vent box.

•Minimum vent length of straight pipe between fire- place and the DV Power Vent box is:

10 feet for units with input up to 33,000BTU/h;

15 feet for units with inputs from 33,000BTU/h to 40,000BTU/h.

•Maximum vent length of straight pipe between the DV Power Vent System box and the vent termination is 6 FT.

•Only vent components manufactured by CFM Corpo- ration are approved for use with this DV Power Vent System.

•All 4” and 7” venting connections (twist-lock or crimped ends) to be sealed with high temperature silicone.

•The 4” and 7” pipes connected to the inlet side of the DV Power Vent System box to be fitted inside the 4” pipe and the 7” collar.

•Leave a permanent access for inspection and service of the DV Power Vent System box.

•Confined area definition: when the distance of the four walls around the sides of the Power Vent Box to the stand-offs is 3” or less in average.

•When the DV Power Vent box is installed in a con- fined area, the access door needs to have a mini- mum size of 12” X 12” and it must be ventilated with a minimum of 10% open area. In a confined area installation a minimum distance of 12” (1FT), needs to be left between the Power Vent Box and the fifth wall. (Refer to Figures on Page 5).

•When the DV Power Vent box is installed in an un- confined area, the access door doesn’t need to be ventilated.

•The power vent motor shaft MUST ALWAYS BE ori- ented horizontally for proper operation.

•The pressure switch diaphragm MUST ALWAYS BE, in a vertical position and the hose connection point- ing down, NEVER up.

•Disconnect power supply when installing or servicing the fireplace or the power vent system.

10003262

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents DV Power Vent System Model 7PDVS Table of Contents DV Power Vent System DV Power Vent System Parts and Description Confined Area Access Door Suggestions Clearance to Combustible Materials and Access DoorModels Input BTU/h Restrictor Orifice Size Restrictor Orifice Sizes and ModelsChanging the Restrictor Orifice Plate Installing the DV Power Vent SystemFour different ways to install the Power Vent System Box Install the Vent Pipes and the DV Power Vent System BoxVenting Up Venting Down Figure a Wire ConnectionsAdding Deflectors to the Side Wall Vent Termination Wiring Diagram Honeywell Ignition Module Wiring Diagram Synetek Ignition Module Operation of the DV Power Vent System DV Power Vent System Screws Troubleshooting the Power Vent System Is working? 7PDVS DV Power Vent System 7PDVS DV Power Vent System DV Power Vent System DV Power Vent System CFM Corporation

7PDVS specifications

The Vermont Casting 7PDVS, a wood-burning stove, is a hallmark of efficient heating technology combined with exceptional craftsmanship. Designed with both aesthetics and functionality in mind, this stove serves as an exemplary addition to any home, providing warmth while enhancing the interior decor.

One of the standout features of the 7PDVS is its impressive thermal efficiency. With a heating capacity of up to 2,500 square feet, it’s capable of warming large areas with ease. The stove utilizes advanced combustion technology, allowing for a longer burn time and reduced emissions. This efficiency not only translates to lower fuel expenditure but also makes the Vermont Casting 7PDVS an environmentally friendly option.

The stove is constructed from heavy-duty cast iron, ensuring durability and longevity. The cast iron not only retains heat well but also radiates warmth evenly throughout your living space. The design includes a large viewing window, providing an unobstructed view of the fire, which adds a cozy ambiance to any room. The window is equipped with air-wash technology that keeps it clean, offering a clear view of the flames even during extended use.

Another significant characteristic of the Vermont Casting 7PDVS is its adaptable design. It features both a top and rear flue outlet option, providing flexibility for installation in various layouts. This versatility ensures that homeowners can integrate the stove seamlessly into their existing spaces.

The Vermont Casting brand is renowned for its emphasis on quality craftsmanship, and the 7PDVS is no exception. Each unit undergoes stringent testing to guarantee consistent performance and safety. Moreover, the stove's cast iron is available in multiple finishes, allowing homeowners to customize it to match their decor.

In summary, the Vermont Casting 7PDVS excels with its combination of efficiency, durability, aesthetic appeal, and versatile installation options. It is not merely a stove; it is an investment in comfort and style, making it a popular choice for those seeking a reliable heating solution that will stand the test of time. With its innovative technologies and commitment to quality, the 7PDVS sets a benchmark in the world of wood-burning stoves, appealing to both traditional and modern homeowners alike.
Top Page Image Contents