Vermont Casting 647 BFC Installing Top Housing or Termination, Installing Chimney in a Chase

Page 13

Installing Top Housing or Termination

Follow the installation instructions provided with the CFM Corporation chimney termination you have se-

lected.

Installing Chimney in a Chase

Refer to Page 4, Figure 2 for an illustration of a typical chase installation.

CAUTION: Treatment of firestop spacers and construc- tion of chase may vary with type of building. These instructions are not a substitute for local building codes. You must check your local building codes to determine specific requirements for your city or state. NOTE:

BFC36 Balance Flue Heat-Circulating Fireplace

Air Space Clearances

Combustible framing material MUST NOT penetrate AIR SPACE (shaded areas).

2”

Standoff

¹⁄” air space to

sides

Other building materials may be required in addition to

firestop spacers.

Finishing

CAUTION: All joints between the finished wall and the fireplace surround (top/sides) must be sealed with non- combustible material to prevent cold air leakage into the room. Only noncombustible material may be applied to the facing of the fireplace surround. (Black painted

area) (Fig. 18)

Finish Wall

Finish the wall with material of your choice. Do not install a combustible mantel shelf less than 12” (305mm) above the grille opening. Do not install a mantel face plate less than 6” (159mm) from top of grille opening. (Fig. 20) If a combustible material is used below a flat mantel shelf, consult your local build- ing codes for minimum clearance from top of fireplace opening to bottom of mantel shelf.

All joints (top, bottom and sides) where wall or deco- rative facing material meets fireplace surround must be completely sealed with a noncombustible material.

FRONT VIEW

Wall

Shield

Only noncom- bustible material may be applied as facing to the black fireplace surround.

SIDE VIEW

Firestop

1” Air Space to Back

¹⁄” Air Space to Sides

0” Clearance to

Floor

Hearth Extension

FPC559a

(Figures 19 and 20)

NOTE: No side wall protection is required for fireplaces installed at 45° to two (2) side walls (corner installation).

Fig. 18 Minimum clearances to combustibles.

7412647

13

Image 13
Contents BFC Table of Contents Safety InformationBFC36 specifications and framing BFC36 Balanced Flue Heat-Circulating FireplaceFireplace and chase parts identification Chimney Requirements Offset Installations Mounting the Fireplace Planning InformationPlanning the Chimney Run Ten Foot RuleChimney Supports InstallationInsulating Fireplace Enclosure For Cold Climates Straight-Up Chimney Installation Installing Electrical WireFraming Chimney Set-upCeiling Chimney Hole Possible Obstructions Offset InstallationCutting the Hole Framing the Ceiling HoleSafety strip installation Positioning, Safety Strips Securing the FireplaceInstalling the Firestop Spacer Installing Chimney SystemProper Firestop Spacer Installation Ceiling HoleInstall Remainder of Chimney Sections Continue Installing Pipe to Complete RunCanadian Requirements For Insulation Shield Additional CeilingsInstalling Chimney in a Chase Installing Top Housing or TerminationFinishing Finish WallFrom top of grille opening. ** 6 from top of grille opening Side Wall Protection Hearth InstallationFinish Glass Doors Common Materials and FactorsGlass Door Operation Installing Line for Gas LogsBFC Balanced Flue Fireplace BFC Balanced Flue Fireplace HPC-1 AccessoriesComponent Description Model Number Chimney ComponentsBFC36 Balance Flue Heat-Circulating Fireplace Limited Warranty & 30 Year Protection Plan CFM Specialty Home Products

647 BFC specifications

The Vermont Casting 647 BFC, a renowned wood-burning stove, combines timeless design with advanced technology, making it a popular choice among homeowners seeking both efficiency and aesthetics. With its robust construction and classic look, the 647 BFC stands as a statement piece in any living space while delivering a high level of performance.

One of the standout features of the Vermont Casting 647 BFC is its exceptional heating capacity. Designed to warm spaces up to 2,000 square feet, this stove is ideal for residential use, particularly in larger homes or open-concept layouts. The 647 BFC utilizes a large firebox that can hold logs up to 22 inches in length, allowing for extended burn times and less frequent refueling, making it not only convenient but also energy-efficient.

A key technology incorporated into the Vermont Casting 647 BFC is its soapstone lining. This material retains heat longer than traditional steel, ensuring a steady release of warmth even after the fire has died down. This feature contributes to the overall efficiency of the stove, minimizing fuel consumption and promoting a cleaner burn. The stove also features an adjustable air control system, which allows users to fine-tune the burn rate, enhancing efficiency and reducing emissions.

Moreover, the 647 BFC is designed with style and versatility in mind. Its traditional appearance, characterized by a cast iron body and elegant detailing, makes it a fitting addition to both modern and rustic interiors. Available in a variety of finishes, including classic black and vibrant colors, homeowners can find a model that complements their decor.

Safety is a paramount consideration in the design of the Vermont Casting 647 BFC. Equipped with a solid cast iron door and a secure latch, the firebox remains contained, preventing accidental contact with flames. Additionally, the stove features a raised grate system that allows for ash to fall through, keeping the firebox cleaner and reducing maintenance.

In summary, the Vermont Casting 647 BFC combines classic aesthetics with modern technology for an exceptional wood-burning experience. Its impressive heating capabilities, efficient design, and safety features solidify its position as a top choice for anyone looking to enhance their home's warmth and charm. Whether used as a primary heat source or a cozy addition to a living space, the 647 BFC is a testament to quality craftsmanship and thoughtful engineering.