Enviro Omega, C-11407, 50-1675, C-11256 owner manual Manual Mode, Thermostat Switch HIGH/LOW position

Page 8
MULTIFUEL
AUTO/OFF
HIGH/LOW
MANUAL
Figure 3: Thermostat Switch in
MANUAL position.

Operating Instructions

PRE-BURN CHECK: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube and locked in place. Check the hopper for enough pellets to start the unit.

Note: Fuel Type can only be changed when the unit is cold. The thermostat mode can be changed during normal operation.

The unit has an automatic cleaning cycle; every thirty (30) minutes the agitator will turn continuously for one (1) minute to help clean out the burn pot liner.

MANUAL MODE:

All control of circuit board function is adjusted at the circuit board.

INITIAL START-UP: Press the ON / OFF button. The stove will turn on. The Fuel Type Light will flash (the Auger Feed Rate is pre-

programmed during start-up). The Heat Level Indicator will show the Heat Level that the stove will run at after start-up.

If this is the first time the unit has been started or the unit has run

out of fuel, the auger may need to be primed. If there is no fuel in the burn pot after two (2) minutes press the Feed Trim button until fuel starts to drop into the Burn Pot Liner (see “OPERATING INSTRUCTIONS;

CONTROL BOARD FUNCTIONS”).

The agitator will not operate for the first five (5) minute after the ON button has been pressed. After the five (5) minutes it will pulse at the same interval as the feed auger.

When the start-up sequence is complete the unit will ramp up to its heat level setting, this may take up to ten (10) minutes.

Once a fire has been established, the convection blower will turn on after ten (10) minutes and the Fuel Type Light will turn solid.

To OPERATE: Press the Heat Level buttons to change the desired Heat Level Output setting. The speed of the convection blower is controlled by the setting of the heat level.

The Feed Trim button used in conjunction with the Heat Level adjustment buttons to adjust the Feed Trim. It can be increased by two (2) feed settings or it can be decreased by two (2) feed settings.

HIGH/LOW MODE: (Requires a Thermostat or Timer)

INITIAL START-UP: See MANUAL MODE above.

OPERATION: When the thermostat calls for heat (contacts are closed) the stove settings are adjustable as per Manual Mode. When the thermostat contacts open, the HEAT LEVEL and Fans will drop down to the LOW setting until the thermostat contacts close again. The stove will come back to the previous HEAT LEVEL setting when the thermostat contacts close again.

AUTO/OFF MODE: (Requires a Thermostat or Timer)

INITIAL START-UP: See MANUAL MODE above.

OPERATION: When the thermostat contacts close, the unit will light automatically. Once up to temperature, the stove operates the same as in MANUAL. When the thermostat contacts open, the stove’s HEAT LEVEL and Fans will drop down to the LOW setting for 30 minutes. If the thermostat contacts close within the 30 minutes,

MULTIFUEL

AUTO/OFF

HIGH/LOW

MANUAL

Figure 4: Thermostat Switch in

HIGH/LOW position.

MULTIFUEL

AUTO/OFF

HIGH/LOW

MANUAL

Figure 5: Thermostat Switch in

AUTO/OFF position.

the HEAT LEVEL will return to the previous MANUAL setting. If the thermostat contacts remain open, the stove automatically begins its shutdown routine. The stove will re-light when the thermostat contacts close again.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Omega Table of Contents Introduction Store fuels at least 36 1 m away from the pellet stoveSafety Warnings & Recommendations Safety Warnings & Recommendations Dimensions & Specifications Operating InstructionsUnit Overheated Circuit Board Control Panel DecalManual Mode Thermostat Switch HIGH/LOW positionSpecial Notes Slider/Damper Plate in UnitRoutine Cleaning and Maintenance Tools Required to CleanCheck the Burn Pot Liner Daily UnitDo not Place Unburned or RAW Pellet Fuel in ASH PAN Post Season CLEAN-UP Cleaning Painted SurfacesDoor Glass Replacement Firebox LinerTo the Distributor WarrantyTo the Dealer Exclusions and Limitations Warranty Installation Data Sheet Name of Owner Address

50-1675, C-11256, Omega, C-11407 specifications

Enviro C-11407, Omega, and C-11256, 50-1675 are cutting-edge technologies designed to address various environmental challenges through innovative engineering and advanced features. These systems have been developed for a wide range of applications, including waste management, air quality improvement, and resource conservation.

Enviro C-11407, known for its robust design, focuses on waste reduction and recycling processes. This system incorporates a modular architecture that allows for easy integration into existing waste management facilities. With its high-efficiency sorting capability, the C-11407 employs advanced sensors and machine learning algorithms to identify recyclable materials. The system can significantly increase the recovery rates of recyclable materials while reducing operational costs.

Omega technology, on the other hand, is geared towards air quality enhancement. This system utilizes sophisticated filtration and purification methods to remove pollutants from the atmosphere. The Omega unit employs a multi-stage filtration process, which includes HEPA filters, activated carbon, and photocatalytic oxidation, ensuring the highest level of air purification. Its smart monitoring system provides real-time data on air quality, allowing for proactive measures to be taken against pollution spikes, thereby improving public health and environmental conditions.

C-11256 is an advanced energy management system aiming to improve energy efficiency and reduce carbon footprints. This technology integrates renewable energy sources such as solar and wind with smart grid capabilities. The C-11256 utilizes energy storage systems that can store excess energy for use during peak demand times. Its predictive analytics feature allows users to optimize energy consumption, contributing to substantial cost savings and a decrease in greenhouse gas emissions.

The 50-1675 model represents a versatile solution for water treatment applications. This system features advanced membrane filtration technology capable of removing contaminants at the molecular level. With a focus on sustainability, the 50-1675 is designed to minimize water wastage while maximizing contaminant removal efficiency. Its compact design makes it suitable for various settings, including industrial processes, municipal water treatment, and even portable applications for remote areas.

Together, these technologies—Enviro C-11407, Omega, C-11256, and 50-1675—highlight a commitment to innovation in environmental management. By harnessing cutting-edge engineering and advanced analytical tools, they promote sustainability, enhance resource recovery, and improve overall quality of life for communities worldwide.
Top Page Image Contents