60$17/,1*7+,535,2572,167$//,1 | AEG G20 specification

',60$17/,17+(),5(35,2572,167$//,1

The lower front panel assembly is removed by lifting upwards and pulling forwards. Remove the canopy to gain access to the Bezel or (Goal post trim) securing screws. The canopy is held in position by dimpled spring clips on both the side flanges, remove by exerting an even pull forward. See Fig 11.

Remove the outer bezel/Goal post trim by unscrewing the four M4 taptite screws on the inner flanges and the four No 8 self tapping screws in the corners.

It will be necessary to dismantle the burner from the convector box before installing the box in the opening, to remove the burner, unscrew the two screws securing the fibre back/ side cheek assembly in position and remove, remove the coal support shelf and burner inserts. Unscrew the two screws at the base of the aperture in the fascia panel and withdraw the burner.

,167$//,1*7+($33/,$1&(,1326,7,21

With the gas supply pipe laid to the required position and the surround fitted and sealed to the chimney correctly – this is to prevent any seepage of the flue products and to prevent any ingress of air into the flue from anywhere other than the flue outlet of the fire. The method to be used to secure the appliance in position is either screwed directly onto the front face of the back panel through the mounting brackets or fixed to the internal side walls of the builders opening using the four fixing brackets provided. These can be rotated to accommodate most openings, as shown in Fig 14: plastic plugs and wood screws are supplied for these brackets.

It is very important when fitting the trim, that when it is secured in position, that the rear of the trim has an effective seal with the back panel or fixing wall. ( A seal is fitted to the trim during manufacture).

Continue the supply and replace the burner ensuring that the rear legs locate in the two up-formed tags in the base plate and complete the gas connection to the burner. Replace the canopy.

NOTE: Before offering the convector box into the opening, the hearth should be protected from damage or scratches that may occur during installation.

The complete installation should be tested for Gas soundness.

IT IS VERY IMPORTANT THAT THE RESTRICTOR PLATES ARE REMOVED AND THE SCREWS REPLACED WHEN THE APPLIANCE IS INSTALLED INTO EITHER A PRE-CAST OR A 5in (125mm)

DIAMETER FLUE.

$66(0%/<2)7+()8(/%('&20321(176

1.Locate the fibre back/side cheek assembly in position.

2.Place the coal support shelf on the stainless steel channel, the machined groove on the underside of the shelf is located on the rear flange of the channel.

3.Place the two shaped burner inserts in channel between the two burner flame ports, (check that a minimum gap of approx. 6mm is maintained between the rear of the burner insert and the front edge of the coal support shelf).

4.Position the front simulated coal on the shelf provided above the control facia panel. See fig 20.

&2$//$<287

Position 3 large coals, 2 triangular and 4 large coals on edge (straddle the gaps of the coal support shelf and run the strata front to rear) as the first layer (fig. 21). Place 4 medium as a second layer sitting on the gaps of the front coals and resting against the rear coals.(fig 22). Finally place the remaining 5 small coals as shown in fig 23. Small adjustments to the coal layout may be made to give the best visual appearance however, additional coals must not be used. If any fibre component is lost or broken the appliance must not be used until a replacement is obtained.

Page 7

G20 specifications

The AEG G20 is a highly regarded washing machine that integrates advanced technology with efficient performance, making it a popular choice for modern households. One of the standout features of the G20 is its innovative ProSense technology, which intelligently detects the load size and adjusts the duration of the wash cycle accordingly. This ensures optimal cleaning results while minimizing water and energy consumption, catering to the growing demand for sustainable appliances.

The G20 boasts a remarkable A+++ energy rating, placing it among the most energy-efficient machines available. This not only helps in reducing utility bills but also lessens the environmental impact of laundry day. Users can benefit from the machine's quick wash feature, which allows for a comprehensive clean in as little as 20 minutes, perfect for those busy days when time is of the essence.

Another notable aspect of the AEG G20 is its range of specialized programs designed to handle various fabric types and soil levels. Programs include settings for delicate items, woolens, and heavy-duty fabrics, ensuring that every garment receives the appropriate care. For example, the "Night Cycle" option guarantees quieter operation during late hours, allowing for uninterrupted rest in the household.

The AEG G20 is equipped with an intuitive display and user-friendly controls, making it easy for anyone to operate. The child lock feature enhances safety, preventing accidental changes to settings or interruptions during operation. Moreover, the machine has a generous load capacity, accommodating a significant amount of laundry, which is ideal for larger families.

In terms of build quality, the G20 is designed with durability in mind. Its robust materials and construction minimize vibrations during operation, leading to a quieter performance and a longer lifespan for the appliance. Additionally, the AEG G20 is designed with a sleek, modern aesthetic, making it a stylish addition to any laundry room.

Overall, the AEG G20 stands out for its blend of cutting-edge technology, energy efficiency, and thoughtful design, making it a reliable choice for consumers looking to maintain cleanliness and sustainability in their laundry practices.