Weber 42377 manual Connect GAS Supply, Regulator, Test Connections

Page 7

GAS INSTRUCTIONS

TEST CONNECTIONS

All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54.

DANGER

Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death, and damage to property.

REGULATOR

•The regulator should be adequately supported.

•The regulator must be installed close to the appliance.

•Each appliance must have a separate regulator.

CONNECT GAS SUPPLY

1)Uncap the fl are fi tting from the optional side burner connection located at regulator.

Note: You must connect your side burner to a Weber® approved regulator(part number #62434) located at main gas supply. If you do not use a Weber® approved regulator the Warranty on the Summit® Built-In Side Burner will be voided.

If you have any questions, contact Customer Service at 1-800-446-1071

2)Connect the corrugated gas line to the side burner Connection.

top view

Cap (Optional Side Burner)

Hard piped gas supply

Figure 1

Regulator

top view

Hard piped

to side burner

gas supply

 

Test connections

All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of ANSI Z223.1/NFPA 54.

DANGER

Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death, and damage to property.

WARNING: You should check for gas leaks every time you disconnect and reconnect a gas fitting.

Note - All factory-made connections have been thoroughly checked for gas leaks. As a safety precaution however, you should recheck all fi ttings for leaks before using your Summit® Built-In side burner. Shipping and handling may loosen or damage a gas fi tting.

You will need: a soap and water solution, and a rag or brush to apply it.

Turn on gas supply.

Check for leaks by wetting the connections with the soap and water solution and watching for bubbles. If bubbles form or if a bubble grows, there is a leak.

Note - Since some leak test solutions, including soap and water, may be slightly corrosive, all connections should be rinsed with water after checking for leaks.

WARNING: Do not ignite burners when leak check- ing.

Regulator

Figure 2

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Summit BUILT-IN NG Side Burner INSTALLATION/OWNERS GuideLiquid Propane GAS Units only Warranty WarrantyLocating Your BUILT-IN Side Burner GAS InstructionsClearance from Combustible Surfaces or Structures Mounting Side Burner BUILT-IN GAS Line LocationsGeneral Construction Details General Specifications for Piping Typical Natural GAS Supply InstallationGAS Line Piping Regulator Connect GAS SupplyTest Connections Lighting the side burner Side Burner Lighting InstructionsManually Lighting the Side Burner Replace Igniter Batteries OperatingTo Extinguish Problem Check Side Burner Troubleshooting
Related manuals
Manual 12 pages 30.93 Kb

42377 specifications

The Weber 42377 Summit Built-In NG Side Burner is a high-performance addition to outdoor kitchens, designed to elevate your grilling experience with its advanced features and robust construction. This side burner is an integral component of the Weber Summit series, renowned for its commitment to quality and innovation.

One of the standout characteristics of the Weber 42377 is its powerful burner system. Equipped with a premium stainless steel burner, it delivers an impressive 12,000 BTUs of cooking power. This ensures rapid heating and exceptional temperature control, allowing you to prepare a variety of dishes with ease. Whether you’re sautéing vegetables, boiling sauces, or whipping up side dishes, this side burner can handle the task efficiently.

The construction of the Weber 42377 is another highlight, featuring durable stainless steel materials that not only enhance its aesthetics but also ensure longevity. Stainless steel is resistant to rust and corrosion, making this side burner ideal for outdoor use where it is subjected to varying weather conditions. Additionally, the sleek design integrates seamlessly into any outdoor kitchen setup.

The side burner includes an easy-to-use electronic ignition system, which allows for quick and hassle-free startup. With just a push of a button, the burner lights up, saving time and effort compared to traditional match-lighting techniques. This convenience is complemented by the convenient control knobs that provide precision heat adjustments, letting you fine-tune the cooking temperature to suit your culinary needs.

Another notable feature is the locked lid design. When not in use, the lid can be securely locked, keeping the burner safe from the elements and preventing debris accumulation. This attention to detail reflects Weber’s dedication to usability and maintenance.

Furthermore, the Weber 42377 Summit Built-In NG Side Burner is designed to be compatible with natural gas, making it an efficient choice for homeowners looking for a reliable, permanent cooking solution. With its thoughtful features and durable construction, this side burner exemplifies Weber's commitment to enhancing the outdoor cooking experience, making it an essential addition for grilling enthusiasts. Whether you’re hosting a barbecue or enjoying a quiet evening cookout, the Weber 42377 provides the versatility and performance needed to create delicious meals with ease.
Top Page Image Contents