Martin Fireplaces VFCS30SNV, VFCS20SPV manual Checking GAS Pressure and Connecting Remote Receiver

Page 15

CHECKING GAS PRESSURE AND CONNECTING REMOTE RECEIVER

The heater gas inlet connection is 3/8" NPT at the valve. The

WARNING

 

 

inlet is located on left side of stove. Remove front control plate

Connecting directly to an unregulated

 

to better access the inlet.

 

 

propane/L.P.G. tank can cause an

When tightening up the joint to the valve, hold the valve securely

 

 

explosion.

with a wrench to prevent movement.

 

 

Test all gas joints from the gas meter to the heater valve for

 

 

 

 

leaks using a gas analyzer or soap and water solution after completing connection. DO NOT USE AN OPEN FLAME. Check the gas pressure with the appliance burning and the control set to HIGH.

MILLIVOLT CONTROL (FIGURE 10)

Test Port “OUT”

The valve regulator controls the burner pressure which should be checked at the pressure test point.

If outlet pressure is low, check inlet pressure against data plates or manual.

Turn captured slotted screw counter clockwise 2 or 3 turns and then place tubing to pressure gauge over test point (Use test point “OUT” closest to control knob). After taking pressure reading, be sure and turn captured screw clockwise firmly to re-seal. Do not over torque. Check for gas leaks.

Figure 10 - Pressure Test Point Location

Milli-Volt Control

NOTE: Remove control panel to access gas valve and ignitor battery module.

CONNECTING REMOTE RECEIVER

1.Remove cover on control panel to show opening for remote receiver. See Figure 11.

2.Cut cable to length (approximately 12") for placement in the fireplace.

3.Strip back 1/4" of the insulation from free end of each wire. Do not cut off wire connector.

4.Connect two .25 female connectors to the wires at free end of the cable.

5.Insert the wire connector into the receiver. If remote does not have plug-in connector, strip back 1/4" of insulation. Insert wire into terminal and tighten screws.

6.Connect the connectors to the two .25" male connectors located on the left side when facing the unit. See Figure 11. Do not let the wire touch the grate or burners.

7.Slide remote receiver in the opening of control panel. Use two screws provided to attach remote receiver to the control panel. See Figure 11.

8.Replace Cover. See Figure 11.

NOTE: Do not place remote in combustion chamber.

Remote Receiver

Cover

Figure 11 - Installing Remote Receiver

58D6003

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models VFCS20SNV VFCS30SNV VFCS20SPV VFCS30SPV What to do if YOU Smell GASRead and Save These Instructions Contents Important Safety Information InstallerOwner From Optional Door Store Break-Away Knob Handle Here Product FeaturesOn/Off Switch Optional Remote Receiver Piezo Hi/Lo Knob Break-Away Handle28 1 DimensionsVFCS20S VFCS30S 26 3What YOU will Need for Installation Getting StartedMake Sure YOU have Received ALL Parts Product Specifications General Installation Information CodesAdequate Combustion and Ventilation AIR L1 = 151/2 Ft., L2 = 12 Ft., W = 12 Ft., H = 8 Ft Counter Cast Iron StoveClearances / Height Requirements Ceiling Side Wall MantelCeiling Placing Stove in Alcove Clearances / Height RequirmentsRemoving Unit from Crate Flexible Tube Manual Shutoff Gas Supply Inlet Valve Connecting the GASRemote Receiver Cover Checking GAS Pressure and Connecting Remote ReceiverConnecting Remote Receiver Millivolt Control FigureComplete Millivolt System Check Electrical Wiring MILLI-VOLTConnecting Optional Wall Switch or Thermostat Checking System OperationOptional Fan Operating Thermostat SensorThermo Bulb Plastic Clip Piezo Ignitor Hi/Lo Knob PilotTop Left Log #4 Bottom Log #2 Support Bracket LOG PlacementFor Natural Thermocouple For LP Rock Wool InstallationBend in Rock Wool Tray Rock Wood ThermocoupleMiddle Log Flame AppearanceChecking Burner Flame Operating InstructionsOff/Pilot/On Knob Optional Thermostat Sensor Operating InstructionsMILLI-VOLT and Thermostat Control Lighting Instructions Cleaning and Servicing Operating Instructions and Cleaning and ServicingObserved Problem Possible Cause Remedy TroubleshootingODS/pilot lights, but flame Logs Replacement Parts ListBurner Assembly Replacement Parts58D0061 58D0056 VFCS20 VFCS3033D0070 33D0071 58D0193 58D043558D6003 58D6003 58D6003 Limited Lifetime Warranty

VFCS20SNV, VFCS20SPV, VFCS30SNV, VFCS30SPV specifications

Martin Fireplaces is renowned for crafting elegant and efficient heating solutions, and their line of VFCS fireplaces exemplifies this reputation. The VFCS30SNV, VFCS20SPV, VFCS20SNV, and VFCS30SPV models are designed to provide optimal warmth and comfort in any setting while enhancing interior aesthetics.

The VFCS30SNV is a powerhouse, showcasing a sleek, modern design that easily integrates into various home decor styles. Its remarkable heating capacity makes it suitable for larger spaces, ensuring that every corner remains cozy. This model features an impressive burn efficiency, allowing for longer intervals between refueling and maximizing fuel usage. Additionally, the advanced airflow technology ensures that heat is distributed evenly across the room, eliminating cold spots.

Alternatively, the VFCS20SPV offers a slightly more compact design without compromising on performance. This model is perfect for smaller rooms or as a supplementary heating source. With its innovative ignition system, the VFCS20SPV allows users to start a fire quickly and conveniently. This is paired with a built-in safety mechanism, ensuring peace of mind while enjoying the warmth.

The VFCS20SNV continues with a similar design philosophy, offering a contemporary aesthetic along with robust functionality. Its large viewing window showcases the beautiful flames, creating a warm and inviting atmosphere. The adjustable flame height feature provides users with control over the ambiance, catering to different moods or occasions.

Lastly, the VFCS30SPV stands out with its dual-fuel capability, providing versatility in fuel choice between gas and propane. This adaptability makes it a favorite among homeowners looking for customizable options. The model also includes a remote control, allowing users to adjust settings from the comfort of their couch.

All models boast high-efficiency ratings, ensuring minimal environmental impact and lower energy costs. Moreover, the use of premium-quality materials guarantees durability and longevity, making these fireplaces a worthwhile investment. The combination of cutting-edge technology and thoughtful design makes Martin Fireplaces' VFCS line a top choice for anyone seeking a stylish and efficient heating solution. Whether you prefer the larger VFCS30 models or the more compact VFCS20 options, you can expect warmth, comfort, and elegance in any setting.
Top Page Image Contents